Belts and pulleys: pulley speed ratio, torque, belt length, wrap angle and alignment explained

Learn how a belt drive changes speed and torque (n1 × d1 = n2 × d2), how long a belt must be, why the small pulley slips first and why alignment and tension matter. Spin two pulleys at the right speeds, change their sizes and spacing, and see chains and sprockets too.

Keep it one tap away for everyday use.

Bookmark Belts and pulleys?

Press Ctrl + D now. Your browser opens its own bookmark box, where you choose the name and folder.

Or install fibub as an app: every tool you open then works offline.

  1. Set pulleys
  2. Watch spin
  3. Speed, belt
Nothing is uploadedWorks offline once open

Stay safe

  • This lesson explains the physics. It is not training to work on machines.
  • Never reach towards a running belt or chain. Where the belt meets the pulley (the in-running nip) it pulls fingers, sleeves and hair in faster than you can react.
  • Guards stay on. Belts are only looked at or touched with the machine switched off, isolated and locked out by a trained person, after it has stopped turning.
  • Tie back long hair; no loose sleeves, gloves, ties or jewellery near moving parts.

Where you see them

  • Bicycle chain
  • Car engine belt
  • Washing machine
  • Pillar drill
  • Lawn mower
  • Conveyor
  • Fans and pumps

The big ideas

  1. Same belt, different speeds

    The belt moves at one speed, so both rims do too. A small pulley must turn more times to pass the same length of belt. That gives the rule n1 × d1 = n2 × d2: speed × diameter is the same on both.

    Small driving big slows things down. Big driving small speeds them up.

  2. Slower means stronger

    Power is shared between speed and torque (twisting force). If the driven pulley turns at half the speed, it gives about twice the torque: T2 = T1 × d2 ÷ d1, less a few per cent lost to the belt bending and slipping.

  3. C

    How long is the belt?

    For an open belt with pulley diameters D and d and centre distance C, the length is about L ≈ 2C + π(D + d)/2 + (D − d)² ÷ 4C. Belts are sold by length, so this is how you check the size.

    For real numbers use the belt drive part of the gear trains tool.

  4. Wrap angle and grip

    The belt grips by friction over the part of the pulley it wraps round. The small pulley has less wrap, so it slips first. Pulleys very different in size and close together give little wrap; most belt makers want at least 120°.

  5. tightslack

    Belt tension

    The side being pulled by the driver is the tight side; the other is the slack side. The difference in pull is what turns the driven pulley. Too loose and the belt slips, squeals and glazes. Too tight and it overloads the shaft bearings.

    Makers give a tension or a deflection test for each belt.

  6. Alignment

    Both pulleys must sit in one plane and their shafts must be parallel. A straight edge (or a laser tool) laid across both faces should touch at all four points. Out of line, the belt rubs on one side, wears fast, gets hot and can jump off.

  7. Chains and sprockets

    A chain does the same job with teeth, so it cannot slip: n1 × z1 = n2 × z2, where z is the number of teeth. Chains carry big forces at low speed but need oil and wear, which stretches them.

    A bike in low gear: a small front ring and big back sprocket, so the wheel turns slowly with more torque.

Try it: a belt drive

Shown slowed down: the motor pulley turns once a second at 1,450 rpm.

  • Make both pulleys the same size. What happens to the speed and the torque?
  • Make d2 = 400 mm and d1 = 100 mm, then slide the pulleys close together. Watch the wrap angle on the small pulley drop.
  • Double the motor pulley. Why does the belt speed double too?

Leave it to a qualified millwright or technician when

  • Any belt, chain or guard on a powered machine needs adjusting, changing or removing. That needs isolation, lock-out and training.
  • A belt squeals, smokes, cracks, flaps or keeps coming off, or a chain is stretched, stiff or noisy.
  • Pulleys need aligning or a belt needs tensioning to the maker's figure, often with a laser tool or a tension gauge.
  • You want to change the pulley sizes to make a machine run faster: parts like blades, fans and wheels have speed limits.

Check yourself

What it does

A belt or chain carries turning from one shaft to another, and by using pulleys of different sizes it can make the second shaft turn slower and stronger, or faster and weaker. This lesson explains the physics a millwright uses every day on belt drives. Seven illustrated idea cards cover the speed rule n1 × d1 = n2 × d2, why torque goes the other way, belt length, wrap angle, tension, alignment, and chains and sprockets. In the sim you set the size of the motor pulley and the driven pulley, the distance between them, the motor speed and its power, and watch both pulleys turn at the right speeds (slowed down so you can see them). The table shows the driven speed, the torque on each shaft, the belt speed, the belt length and the wrap angle on the small pulley. A short quiz checks it all.

It is lesson 3 of the free How machines work course, after levers in everyday tools. For a real belt or gear drive use the gear trains tool, and see why belt pull matters to the shafts in bearings and friction.

How to use it

  1. Read the Stay safe box. The lesson explains physics; it is not training to work on belts or machines.
  2. Work through the idea cards, ticking Done as you go (kept only if you tick Remember my ticks on this device).
  3. In Try it, move the sliders. The motor pulley is blue and the driven pulley orange. Press Pause to stop the animation.
  4. Read the driven speed and the table. A warning shows if the wrap angle drops below 120° or the belt speed goes above about 30 m/s.
  5. Take the quiz, then press New questions for another set.

What each number means

  • Speed ratio: d2 ÷ d1. A ratio of 2 : 1 means the driven pulley turns at half the motor speed.
  • Motor torque T1: the motor’s twisting force, from its power and speed: T = P ÷ ω, with ω = 2π × rpm ÷ 60.
  • Driven torque T2: T1 × d2 ÷ d1, ignoring the few per cent a real belt loses.
  • Belt speed: how fast the belt itself moves, π × d1 × n1 ÷ 60.
  • Belt length: the formula L ≈ 2C + π(D + d)/2 + (D − d)²/4C, and the exact length for comparison. They agree to a millimetre or so unless the pulleys are very different and close together.
  • Wrap angle: how much of the small pulley the belt touches. Less wrap means less grip.

Worked example

A motor runs at 1,450 rpm with a 100 mm pulley, driving a 200 mm pulley 500 mm away. Driven speed: 1,450 × 100 ÷ 200 = 725 rpm. The motor is 1.5 kW, so its torque is 1,500 ÷ (2π × 1,450 ÷ 60) = 9.88 N·m, and the driven shaft gets 9.88 × 200 ÷ 100 = 19.8 N·m. Belt length: 2 × 500 + π × 300 ÷ 2 + 100² ÷ (4 × 500) = 1,000 + 471.2 + 5 = 1,476 mm. Wrap on the small pulley: 180° − 2 × asin(100 ÷ 1,000) = 180° − 11.5° = 168.5°, plenty of grip.

FAQs

Which diameter do I use, outside or pitch? For speeds and belt lengths, the pitch diameter: where the belt’s load-carrying cords run. It is a little less than the outside of a V-belt pulley. Makers list it.

Why does the driven pulley run a little slower than the rule says? Belts creep and slip slightly, usually 1 to 2 %. Toothed (timing) belts and chains do not.

Can I just fit a bigger pulley to make a machine faster? No. Blades, fans, grinding wheels and pumps have speed limits, and the motor may be overloaded. That is a job for a qualified technician.

What does a crossed belt do? It makes the driven pulley turn the other way. It is rare now; the gear trains can work one out.

Where the numbers come from

  • Speed ratio n1 d1 = n2 d2, torque T = P ÷ ω, belt speed v = π d n ÷ 60, the open belt length approximation L ≈ 2C + π(D + d)/2 + (D − d)²/4C and the exact form with sin β = (D − d)/2C, and the wrap angle 180° − 2 asin((D − d)/2C): standard machine design formulas found in engineering textbooks and belt makers' design manuals.
  • The 120° least wrap angle and about 30 m/s top speed for ordinary V-belts are common rules of thumb in belt makers' manuals; real limits depend on the belt, so check the maker's data. Drawings are fibub's own.

Standard scientific values, such as constants, atomic weights and melting points, are facts found in every textbook; we name where ours were checked. If you are an author or publisher and want a value, a credit or a table changed or removed, tell us and we will act quickly.

Last updated 2026-11-16.

Change log for Belts and pulleys

  1. Learn: How machines work lessons #L382 levers in tools, #L383 belts and pulleys, #L384 bearings and friction Details on GitHub

Every change to fibub

Related tools

Gear trains #T440 Work out the speeds, directions, torques and power of each shaft in a simple, idler or compound gear train with mesh efficiencies and centre distances; solve a planetary gear set with the Willis equation (any member held or driven, assembly checks, torque split); and find the belt length, wrap angles and driven speed of an open or crossed belt drive, or the centre distance for a belt length. Bearing life #T442 Work out a rolling bearing's L10 life in revolutions and hours from its rating C and the equivalent load P = X Fr + Y Fa (your catalogue values), adjusted for reliability and aISO, or the C you need for a target life. Size a solid round shaft for combined bending and torsion in fatigue (DE-Goodman with your endurance limit) and statically (von Mises and maximum shear), or check the safety factors of a given diameter. Simple machines lab #L13 Lift a load with a lever, a pulley system of 1 to 4 strands, a ramp or a wheel and axle; see the effort you need, the mechanical advantage, the velocity ratio and the efficiency, and check that work out is never more than work in. Levers in everyday tools #L382 See why a claw hammer pulls nails, a long wheel brace undoes tight nuts and a wheelbarrow carries 80 kg. Slide your hand along the handle and watch the push you need change, sort tools into class 1, 2 and 3 levers, and check the principle of moments. Bearings and friction #L384 See why a ball bearing lets a flywheel coast for hours while a dry bush stops it in two minutes. Learn sliding and rolling friction, plain, ball and roller bearings, what grease does, why bearings fail and the warning signs, then name the parts of a ball bearing. Mirror ray diagram #L1 Drag an object in front of a concave or convex mirror and watch the principal rays find the image: where it forms, how big it is, real or virtual, with the mirror formula and magnification worked out with signs.