Home / Courses / GATE Physics / Practice / p-n junctions, diodes and Zener diodes

p-n junctions, diodes and Zener diodes

Solid state physics and devices · 33 questions and templates for GATE Physics, in order from warm-up to top rank. Check each answer, then read the full solution.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. MCQWarm-up

    At a typical operating current of about 10 mA, which of these has the largest forward voltage?
    1. a silicon rectifier diode
    2. a germanium diode
    3. a red LED
    4. a blue LED
    Answer and solution

    Answer: D

    The forward voltage is roughly the band gap in electron-volts divided by e, plus a little: germanium about 0.3 V, silicon about 0.7 V, a red LED (Eg≈1.9 eV) about 1.8-2 V and a blue LED (Eg≈2.7 eV, InGaN) about 3 V. Bluer light means bigger photons, so a bigger gap and a bigger voltage.

    Why people get this wrong: Thinking all diodes drop about 0.7 V: that figure is specific to silicon.

  2. MSQStandard

    Which statements about breakdown in p-n junctions are correct?
    1. Zener breakdown happens in heavily doped junctions.
    2. The Zener mechanism is quantum-mechanical tunnelling of electrons across a very thin barrier.
    3. The avalanche breakdown voltage decreases as temperature rises.
    4. Diodes that break down near 5 to 6 V have a temperature coefficient close to zero.
    Answer and solution

    Answer: A, B, D

    Heavily doped: true: the depletion layer is thin and the field enormous. Tunnelling: true. Avalanche falls with T: false. Hotter lattices vibrate more, carriers lose energy in more collisions and need a higher field to start an avalanche, so the avalanche voltage rises (positive coefficient). Zener breakdown has a negative coefficient (the gap shrinks with T). Near 5 to 6 V: true: both mechanisms share the work and the two effects nearly cancel.

    Why people get this wrong: Remembering only that "Zener diodes" break down; most Zener diodes above about 6 V actually work by avalanche.

  3. MCQStandard

    For an abrupt junction with built-in potential V0 under reverse bias VR, the depletion (junction) capacitance varies as
    1. (V0+VR)−1
    2. (V0+VR)−1/2
    3. (V0+VR)1/2
    4. (V0+VR)−1/3
    Answer and solution

    Answer: B

    The depletion layer acts like a parallel-plate capacitor of gap W: C=εA/W, with W∝(V0+VR)1/2 for an abrupt junction. So C∝(V0+VR)−1/2. A linearly graded junction gives the −1/3 power. Varactor diodes use this voltage-controlled capacitance to tune circuits.

    Why people get this wrong: The −1/3 law belongs to a graded junction, not an abrupt one.

  4. NATStandard

    An LED that drops 2.0 V at its rated current of 15 mA is run from a 5.0 V supply through a series resistor. The resistor needed is ______ Ω (to the nearest whole number).
    Answer and solution

    Answer: 200 $\Omega$ (±1)

    The resistor takes the rest of the supply voltage: 5.0−2.0=3.0 V at 15 mA, so R=3.0/0.015=200 Ω. It dissipates 3.0×0.015=45 mW, so a 14 W part is fine.

    Why people get this wrong: Using the whole 5.0 V (333 Ω): the LED's own drop must be subtracted first.

  5. MCQStandard

    A Schottky (metal-semiconductor) diode is preferred over a p-n diode in fast switching circuits mainly because
    1. it has a higher reverse breakdown voltage
    2. current is carried by majority carriers, so almost no minority charge is stored and it switches off almost at once
    3. its reverse leakage current is smaller
    4. it emits light when forward biased
    Answer and solution

    Answer: B

    In a forward-biased p-n diode, minority carriers are injected and stored on each side; switching off means removing that charge, which takes time (reverse recovery). A Schottky diode conducts by majority carriers crossing the metal-semiconductor barrier, so there is almost no stored charge. It also has a lower forward drop (about 0.2-0.4 V). Its drawbacks are a larger reverse leakage and usually a lower breakdown voltage.

    Why people get this wrong: Choosing "lower leakage": Schottky diodes leak more than p-n diodes.

  6. NATExam level

    A silicon junction (εr=11.7) has Na=1017 cm−3, Nd=1015 cm−3 and built-in potential 0.714 V. At zero bias its depletion width is ______ μm (to two decimal places).
    Answer and solution

    Answer: 0.97 μm (±0.01)

    W=2εV0e(1Na+1Nd) in SI units: Na=1023, Nd=1021 m−3. 2×11.7×8.854×10−12×0.7141.602×10−19=9.23×108; times 1.01×10−21 gives 9.33×10−13 m2; root: W=0.97 μm, almost all on the lightly doped n side.

    Why people get this wrong: Leaving densities in cm−3 inside an SI formula changes the result by a factor of 1000.

  7. MSQExam level

    Which statements about the reverse saturation current Is of a p-n junction diode are correct?
    1. It depends strongly on temperature.
    2. It is larger for a germanium diode than for a similar silicon diode.
    3. It is proportional to ni2.
    4. Below breakdown, it grows steeply with the reverse voltage.
    Answer and solution

    Answer: A, B, C

    Temperature: true: roughly doubling every 10 K in Si. Ge larger: true: Ge has a smaller gap and ni about 103 times larger. ∝ni2: true: Is=eAni2(DpLpNd+DnLnNa), from minority carriers ni2/N diffusing to the junction. Grows with VR: false: it saturates, because it is limited by how many minority carriers reach the junction, not by the voltage.

    Why people get this wrong: The word "saturation" is the clue: past a few kT/e of reverse bias, the ideal reverse current stops growing.

  8. NATExam level

    A solar cell gives a photocurrent of 30 mA, has reverse saturation current 10−10 A and ideality factor 1, at VT=25.85 mV. Its open-circuit voltage is ______ V (to three decimal places).
    Answer and solution

    Answer: 0.505 V (±0.003)

    With the photocurrent, I=Is(eV/VT−1)−IL. Open circuit means I=0: Voc=VTln⁡(1+IL/Is)=0.02585ln⁡(3×108+1)=0.02585×19.52=0.505 V.

    Why people get this wrong: Expecting Voc to grow in proportion to the light. It grows only logarithmically.

  9. MCQExam level

    For an abrupt p-n junction, the ratio of the depletion widths on the two sides, xn/xp, equals
    1. Na/Nd
    2. Nd/Na
    3. Na/Nd
    4. 1
    Answer and solution

    Answer: A

    The total charge on the two sides must cancel: eNdxnA=eNaxpA. So xn/xp=Na/Nd. The region is wider on the less doped side.

    Why people get this wrong: Nd/Na inverts it. Think of balancing charges: low density needs more width.

  10. NATExam level

    A solar cell has open-circuit voltage 0.60 V and short-circuit current 3.0 A. At its maximum-power point it delivers 2.7 A at 0.50 V. Its fill factor is ______ (to two decimal places).
    Answer and solution

    Answer: 0.75 (±0.005)

    The fill factor compares the real maximum power with the rectangle VocIsc: FF=VmpImpVocIsc=0.50×2.70.60×3.0=1.351.80=0.75. Good silicon cells reach about 0.8; series resistance and shunt leakage lower it.

    Why people get this wrong: Dividing Vmp/Voc only (0.83): the fill factor includes the current ratio too.

  11. MSQExam level

    Which statements about the tunnel diode are correct?
    1. Its depletion region is only a few nanometres wide.
    2. Part of its forward characteristic shows negative differential resistance.
    3. It is used mainly as a high-voltage power rectifier.
    4. Both sides are doped so heavily that they are degenerate.
    Answer and solution

    Answer: A, B, D

    Very heavy doping puts the Fermi level inside the bands on both sides and makes the junction extremely thin, so electrons can tunnel straight through. As forward bias rises, the filled states on one side first line up with empty states on the other (current rises), then slide past them into the gap (current falls: negative resistance), before normal diffusion current takes over. It is used in very fast oscillators and switches; its heavy doping gives it almost no reverse blocking ability, the opposite of a power rectifier.

    Why people get this wrong: Expecting a heavily doped junction to block well: heavy doping makes breakdown (here, tunnelling) happen at very low reverse voltage.

  12. MCQExam level

    A p-n diode carrying a forward current is suddenly reverse biased. For a short "storage time" a large reverse current flows before the diode blocks. This storage time is set mainly by
    1. the minority-carrier lifetime (and the ratio of forward to reverse current)
    2. the depletion capacitance at zero bias only
    3. the thermal voltage kT/e alone
    4. the breakdown voltage
    Answer and solution

    Answer: A

    Forward current builds up stored minority charge Q≈IFτ, with τ the minority-carrier lifetime. On reversal this charge must be swept out by the reverse current or recombine; until it is gone the junction stays forward biased and conducts backwards. A standard estimate is ts≈τln⁡(1+IF/IR). Fast-recovery diodes are made with short lifetimes (e.g. gold doping).

    Why people get this wrong: Blaming the depletion capacitance: it matters after the stored charge is gone, during the final, shorter part of turn-off.

  13. NATHard

    An abrupt junction with built-in potential 0.80 V has capacitance C0 at zero bias. At a reverse bias of 7.2 V its capacitance is ______ C0 (to three decimal places).
    Answer and solution

    Answer: 0.316 (±0.003)

    C∝(V0+VR)−1/2, so CC0=V0V0+VR=0.808.0=0.1=0.316.

    Why people get this wrong: Using VR alone (0.8/7.2=0.333) forgets that the built-in potential adds to the reverse bias.

  14. NATHard

    In a silicon p+-n junction (εr=11.7) the n side has Nd=1016 cm−3 and the depletion region (practically all on the n side) is 1.0 μm wide. The peak electric field is ______ kV/cm (to the nearest unit).
    Answer and solution

    Answer: 155 kV/cm (±1.5)

    Gauss's law through the uniformly charged n region: the field grows linearly from zero at the edge to its peak at the junction, Emax⁡=eNdxnε=1.602×10−19×1022×10−611.7×8.854×10−12=1.55×107 V/m =155 kV/cm (1 kV/cm =105 V/m).

    Why people get this wrong: Using Nd in cm−3 inside SI units, or confusing V/m with V/cm.

  15. NATHard

    A 2.0 V source drives a diode (Is=10−14 A, ideality factor 1, VT=25.85 mV) through a 1.0 kΩ resistor. Solving the exponential diode equation (not the 0.7 V model), the current is ______ mA (to two decimal places).
    Answer and solution

    Answer: 1.34 mA (±0.01)

    Solve I=(2−V)/1000 and V=VTln⁡(I/Is+1) together by iteration. Start with V=0.7: I=1.30 mA, V=0.02585ln⁡(1.30×1011)=0.6619 V. Then I=1.338 mA, V=0.6626 V; then I=1.337 mA. It settles at V=0.662 V and I=1.34 mA, where the load line crosses the diode curve.

    Why people get this wrong: Stopping at the 0.7 V model (1.30 mA). The iteration converges in two or three steps because the log changes slowly.

  16. MCQHard

    Under strong forward bias, the capacitance of a p-n junction is dominated by
    1. the depletion capacitance, which rises steeply in forward bias
    2. the diffusion (storage) capacitance, roughly proportional to the forward current
    3. the capacitance of the metal contacts
    4. nothing: a forward-biased junction has no capacitance
    Answer and solution

    Answer: B

    In forward bias, minority carriers injected across the junction are stored in the neutral regions, and that stored charge changes with voltage: Cd=dQdV=τIηVT, proportional to the current (and the carrier lifetime τ). It soon exceeds the depletion capacitance and limits how fast the diode can switch off.

    Why people get this wrong: Thinking only the depletion layer stores charge; in forward bias the injected carriers store far more.

  17. NATHard

    A silicon diode (ideality factor 1) has minority-carrier lifetime 1.0μs and carries 1.0 mA forward current at VT=25.85 mV. Its diffusion capacitance Cd=τI/VT is ______ nF (to one decimal place).
    Answer and solution

    Answer: 38.7 nF (±0.2)

    The stored minority charge is Q=τI, and I∝eV/VT, so Cd=dQdV=τIVT=(10−6)(10−3)0.02585=3.87×10−8 F =38.7 nF, far larger than a typical depletion capacitance of a few pF.

    Why people get this wrong: Mixing up nF and pF, or using the depletion-capacitance formula.

  18. NATHard

    A one-sided silicon p+-n junction (εr=11.7) has Nd=1016 cm−3 on the n side. Avalanche breakdown occurs when the peak field reaches 4.0×105 V/cm. Neglecting the built-in potential, the breakdown voltage is ______ V (to one decimal place).
    Answer and solution

    Answer: 51.7 V (±0.5)

    In a one-sided junction the depletion region lies in the n side; the field falls linearly from its peak Em=eNdW/ε to zero, and the voltage is the triangle's area, V=12EmW=εEm22eNd. In cm units: ε=11.7×8.854×10−14 F/cm, so VBR=(1.036×10−12)(4.0×105)22(1.602×10−19)(1016)=51.7 V.

    Why people get this wrong: Mixing F/m with cm−3; keep every quantity in cm (or every one in m).

  19. MCQHard

    For a one-sided abrupt junction whose breakdown happens at a fixed critical field, doubling the doping on the lightly doped side changes the breakdown voltage by a factor of about
    1. 2 (it doubles)
    2. 1 (no change)
    3. 1/2 (it halves)
    4. 1/2
    Answer and solution

    Answer: C

    VBR=εEc22eN: at fixed Ec it is inversely proportional to the light-side doping, so it halves. (In real silicon Ec itself creeps up slowly with doping, so the drop is a bit less than half.) High-voltage devices therefore use lightly doped, thick regions.

    Why people get this wrong: Thinking heavier doping makes a junction "stronger": it makes the depletion region thinner and the field rise faster with voltage.

  20. MSQHard

    Which statements about how real silicon diodes depart from the ideal I=Is(eV/VT−1) are correct?
    1. At low forward current, recombination in the depletion region gives an ideality factor near 2.
    2. At high forward current, series resistance makes the log⁡I versus V plot bend over.
    3. In reverse bias the current settles at exactly Is whatever the voltage.
    4. At high-level injection the ideality factor again approaches 2.
    Answer and solution

    Answer: A, B, D

    Recombination through traps in the depletion region gives a current ∝eV/2VT, dominating at low current. At high current the ohmic drop IRs steals voltage from the junction, and high-level injection (injected density comparable to the doping) also changes the slope to about eV/2VT. In reverse bias, generation in the depletion region adds a current that grows with the depletion width, roughly as VR, so the reverse current keeps creeping up rather than saturating.

    Why people get this wrong: Taking "reverse saturation current" literally: in silicon the generation current is usually larger than Is and does not saturate.

  21. NATTop rank

    An abrupt junction has built-in potential 0.75 V. The reverse bias needed to make its depletion width three times its zero-bias value is ______ V (to two decimal places).
    Answer and solution

    Answer: 6 V (±0.02)

    W∝V0+VR. Three times the width needs nine times the total potential: V0+VR=9V0, so VR=8V0=8×0.75=6.00 V.

    Why people get this wrong: Answering 3V0 or 2V0: the width goes as the square root, and the built-in part is already there at zero bias.

  22. MCQTop rank

    Two identical silicon diodes are connected in series with their cathodes joined (back to back), and 5 V is applied across the pair. Which is correct?
    1. Each diode drops 2.5 V and about 2 mA flows.
    2. One diode is forward biased, the current is about the forward current at 0.7 V, and 4.3 V appears across the other.
    3. Almost all of the 5 V appears across the reverse-biased diode, and the current is about the reverse saturation current.
    4. Both diodes are in breakdown.
    Answer and solution

    Answer: C

    Whichever way the voltage is applied, one diode is reverse biased. Only its tiny saturation current Is can flow, and the forward diode needs just VTln⁡2≈18 mV to pass that current. So nearly the whole 5 V sits across the reverse diode and I≈Is (nanoamps or less). Unless 5 V exceeds the breakdown voltage, the pair blocks in both directions.

    Why people get this wrong: Assuming the forward diode takes 0.7 V. That drop belongs to milliamp currents; at Is the forward drop is only tens of mV.

  23. NATTop rank

    A diode drops 0.62 V at 1.0 mA and 0.74 V at 10 mA (both well above Is), at VT=25.85 mV. Its ideality factor is ______ (to two decimal places).
    Answer and solution

    Answer: 2.02 (±0.02)

    For I≈IseV/ηVT: V2−V1=ηVTln⁡(I2/I1). So η=0.120.02585×ln⁡10=0.120.05952=2.02. An ideality factor near 2 suggests that recombination in the depletion region dominates, or that series resistance adds to the drop.

    Why people get this wrong: Using log10⁡ (gives η=4.6).

  24. MSQTop rank

    A Zener regulator must give 10 V to a 500 Ω load (20 mA) from a supply that varies from 15 V to 20 V. The Zener needs at least 2 mA and may carry at most 50 mA. Which choices of series resistor R are correct?
    1. R=150 Ω works over the whole supply range with the load connected.
    2. R=250 Ω works over the whole supply range with the load connected.
    3. R=220 Ω also keeps the Zener safe if the load is disconnected at a 20 V supply.
    4. R=180 Ω also keeps the Zener safe if the load is disconnected at a 20 V supply.
    Answer and solution

    Answer: A, C

    Regulation at the lowest supply: (15−10)/R≥22 mA, so R≤227 Ω. Zener limit at the highest supply with load: (20−10)/R−20≤50 mA, so R≥143 Ω; without load: 10/R≤50 mA, so R≥200 Ω. 150: 33 mA and 67 mA series current, Zener 13 to 47 mA: works. 250: only 20 mA at 15 V, less than load plus 2 mA: fails. 220 unloaded: 10/220=45 mA ≤50: safe. 180 unloaded: 10/180=56 mA: too much.

    Why people get this wrong: Checking only one end of the supply range. The lowest supply limits R from above, the highest supply (and no load) from below.

  25. NATTop rank

    A half-wave rectifier with a capacitor filter runs from a 60 Hz supply and must deliver a steady 50 mA with no more than 1.0 V peak-to-peak ripple. The smallest capacitance needed is about ______ μF (to the nearest μF).
    Answer and solution

    Answer: 833 μF (±8)

    Between peaks (one per cycle in half wave, 1/f apart) the capacitor alone supplies the load: ΔV=IfC. So C=IfΔV=0.05060×1.0=8.33×10−4 F =833 μF. A full-wave rectifier would need half of this.

    Why people get this wrong: Using 2f (the full-wave case) gives 417 μF, which is not enough here.

  26. NATTop rank

    An abrupt junction has capacitance 24 pF at a reverse bias of 1.25 V and 12 pF at 7.25 V. Its built-in potential is ______ V (to two decimal places).
    Answer and solution

    Answer: 0.75 V (±0.01)

    C∝(V0+VR)−1/2, so (C1C2)2=V0+VR2V0+VR1: 4=V0+7.25V0+1.25. Then 4V0+5=V0+7.25, so V0=0.75 V. In the lab this is done by plotting 1/C2 against VR: a straight line that meets the axis at VR=−V0, with a slope that gives the doping.

    Why people get this wrong: Using the capacitance ratio 2 instead of its square 4.

  27. NATTop rank

    A full-wave rectifier with a large reservoir capacitor runs from 50 Hz mains. The output peaks at 20 V and the ripple is 1.0 V peak to peak. Assuming the diodes conduct only while the rectified sine rises from the trough of the ripple to its peak, each conduction interval lasts ______ ms (to two decimal places).
    Answer and solution

    Answer: 1.01 ms (±0.01)

    The diodes switch on when the rectified sine climbs back to the capacitor voltage, 20−1.0=19 V, and off at the peak. Measured back from the peak, Vmcos⁡θ=19, so cos⁡θ=0.95 and θ=18.2∘=0.318 rad. With ω=2π×50=314 rad/s, the interval is 0.318/314=1.01 ms, out of each 10 ms half cycle. All the charge for the next 9 ms is delivered in this short burst, so the diode peak current is roughly ten times the load current.

    Why people get this wrong: Using the full 20 ms mains period, or measuring the angle with sin⁡θ=0.95 (which gives the switch-on instant from the zero crossing, not the interval).

← All topics · Timed mock test →