Home / Courses / GATE Physics / Practice / Electromagnetic induction and inductance

Electromagnetic induction and inductance

Electricity and magnetism · 36 questions and templates for GATE Physics, in order from warm-up to top rank. Check each answer, then read the full solution.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. MCQWarm-up

    A fixed circular loop of area 0.010 m2 sits at rest in a steady, uniform 2.0 T field perpendicular to its plane. The emf induced in the loop is
    1. 0.020 V, because the flux is 0.020 Wb
    2. zero only if the loop has no resistance
    3. zero
    4. 0.020 V divided by the loop's resistance
    Answer and solution

    Answer: C

    Faraday's law: ℰ=−dΦ/dt. The flux is BA=0.020 Wb, but it is not changing, so the emf is zero however large the flux is.

    Why people get this wrong: Mixing up flux with rate of change of flux: a large steady flux induces nothing.

  2. MCQStandard

    A short solenoid (radius r1, n1 turns per metre) sits coaxially inside a long solenoid (radius r2>r1, n2 turns per metre), overlapping it along a length l. Their mutual inductance is
    1. μ0n1n2πr22l
    2. μ0n1n2πr12l
    3. μ0n1n2πr1r2l
    4. μ0(n1+n2)πr12l
    Answer and solution

    Answer: B

    Easiest way: current I in the outer solenoid makes B=μ0n2I inside it. The inner coil has n1l turns of area πr12, so it links μ0n2Iπr12n1l. M=μ0n1n2πr12l. By M12=M21 the other way gives the same.

    Why people get this wrong: Using the outer area: the field of the outer coil only matters where the inner coil is.

  3. MCQStandard

    A toroid of N turns has a rectangular cross-section: inner radius a, outer radius b, height h. Its self-inductance is
    1. μ0N2h2πln⁡ba
    2. μ0N2h(b−a)2πa
    3. μ0Nh2πln⁡ba
    4. μ0N2h(b−a)
    Answer and solution

    Answer: A

    Inside, B=μ0NI/(2πs). Flux through one turn: ∫abμ0NI2πshds=μ0NIh2πln⁡ba. Times N turns, divided by I: L=μ0N2h2πln⁡ba. (B is the thin-toroid approximation, valid only for b−a≪a.)
  4. NATStandard

    A rectangular wire loop of resistance 0.50 Ω is being pulled out of a region of uniform 0.30 T field (perpendicular to the loop) at a steady 2.0 m/s. The side still inside the field, perpendicular to the velocity, is 10 cm long. The pulling force needed to keep the speed steady is ______ mN (to one decimal place).
    Answer and solution

    Answer: 3.6 mN (±0.05)

    The emf is ℰ=Bwv=(0.30)(0.10)(2.0)=0.060 V, so I=ℰ/R=0.12 A. The field acts on the side inside it with force BIw=(0.30)(0.12)(0.10)=3.6×10−3 N, opposing the motion (Lenz). A steady speed needs an equal pull: F=B2w2vR=3.6 mN. The two long sides feel equal and opposite forces that cancel.

    Why people get this wrong: Stopping at the emf or the current; or forgetting that the force is quadratic in B (once to make the current, once to push on it).

  5. MCQStandard

    Inductors of 6.0 mH and 3.0 mH, far apart so they do not affect each other, are connected in parallel. The equivalent inductance is
    1. 2.0 mH
    2. 9.0 mH
    3. 4.5 mH
    4. 18 mH
    Answer and solution

    Answer: A

    In parallel both inductors have the same voltage V=LdI/dt, and the currents add: dIdt=V(1L1+1L2). So 1L=16+13=12 per mH and L=2.0 mH, combining like resistors.

    Why people get this wrong: 9.0 mH is the series value; uncoupled inductors combine like resistors, not like capacitors.

  6. MCQExam level

    The uniform field inside a long solenoid of radius R changes at a rate dB/dt. The induced electric field at distance r from the axis is
    1. r2dBdt inside and zero outside
    2. r2dBdt inside and R22rdBdt outside
    3. rdBdt inside and R2rdBdt outside
    4. zero inside and R22rdBdt outside
    Answer and solution

    Answer: B

    Faraday on a circle of radius r: E(2πr)=dΦdt. Inside, Φ=πr2B, so E=r2dBdt. Outside, Φ=πR2B, so E=R22rdBdt: not zero, even though B=0 there.

    Why people get this wrong: Option A: the induced E outside does not vanish just because B does.

  7. MSQExam level

    The current in a long solenoid is increasing. Outside the solenoid (where B≈0), which are correct?
    1. There is an electric field circling the solenoid.
    2. This electric field is conservative.
    3. Around a closed loop outside that does not encircle the solenoid, ∮E→⋅dl→=0.
    4. ∇×E→=−∂B→/∂t holds there too.
    Answer and solution

    Answer: A, C, D

    Outside, ∂B→/∂t=0, so ∇×E→=0 locally (D), and loops that do not encircle the solenoid give zero (C). But loops that do encircle it give −dΦ/dt≠0 (A), so E→ is not conservative (B is false): the region is not simply connected.
  8. NATExam level

    Two coils of 4.0 mH and 9.0 mH have coupling coefficient k=0.50. Connected in series so that their fluxes add, the total inductance is ______ mH.
    Answer and solution

    Answer: 19 mH

    M=kL1L2=0.5×6=3.0 mH. Series aiding: L=L1+L2+2M=4+9+6=19 mH. (Opposing: 4+9−6=7 mH.)

    Why people get this wrong: Adding M once instead of twice: each coil feels the other's flux.

  9. MCQExam level

    Two coils have self-inductances 4.0 mH and 9.0 mH. Which value of their mutual inductance is impossible?
    1. 2.0 mH
    2. 4.0 mH
    3. 6.0 mH
    4. 7.0 mH
    Answer and solution

    Answer: D

    Always M≤L1L2=6.0 mH (equality for perfect coupling, k=1). 7.0 mH would make the stored energy negative for some pair of currents.

    Why people get this wrong: 7 mH looks plausible because it is less than 9 mH, but the limit is the geometric mean.

  10. MSQExam level

    Which statements about the mutual inductance of two coils are correct?
    1. M12=M21 always.
    2. M depends on the currents in the coils.
    3. Depending on how the coils are connected, M can carry a negative sign.
    4. M2≤L1L2.
    Answer and solution

    Answer: A, C, D

    A: the Neumann formula M=μ04π∮∮dl→1⋅dl→2r is symmetric. B is false: in vacuum (or linear materials) M is set by geometry alone. C: the sign depends on the chosen current directions. D: energy positivity.
  11. NATExam level

    A coaxial cable has an inner conductor of radius 1.0 mm and a thin outer sheath of radius 4.0 mm. Ignoring the field inside the inner conductor, its inductance per metre is ______ μH/m (to three decimal places).
    Answer and solution

    Answer: 0.277 $\mu$H/m (±0.003)

    Between the conductors B=μ0I/(2πs). Flux through a strip of length l: μ0Il2πln⁡ba. So Ll=μ02πln⁡ba=(2×10−7)ln⁡4≈2.77×10−7 H/m. The [capacitor inductor calculator](/science/capacitor-inductor-calculator/) does this for any cable.
  12. NATExam level

    A long solenoid of radius 2.0 cm has its internal field rising at 0.50 T/s. A circular wire loop of radius 10 cm surrounds it coaxially. The emf induced in the loop is ______ mV (to three decimal places).
    Answer and solution

    Answer: 0.628 mV (±0.005)

    Only the flux through the loop matters, and outside the solenoid B≈0, so the flux is that of the solenoid alone: Φ=πa2B. ℰ=πa2dB/dt=π(0.020)2(0.50)=6.28×10−4 V =0.628 mV. The loop's own radius does not appear: a bigger loop enclosing the same solenoid gets the same emf, even though there is no magnetic field at the wire.

    Why people get this wrong: Using the loop's area π(0.10)2 gives 25 times too much; the field is confined to the solenoid.

  13. MSQExam level

    Which statements about induced emf are correct?
    1. A rigid loop moving at constant velocity while staying entirely inside a uniform magnetic field has zero emf.
    2. A rigid loop turning about a diameter perpendicular to a uniform steady field has an emf.
    3. The electric field induced by a changing magnetic field is conservative, so its line integral round a closed loop is zero.
    4. An induced electric field exists only at points where the magnetic field is non-zero.
    Answer and solution

    Answer: A, B

    Moving without turning inside a uniform field leaves the flux unchanged, so ℰ=0 (the motional emfs on opposite sides cancel). Turning changes the angle between B→ and the loop's normal, so the flux changes and there is an emf. ∇×E→=−∂B→/∂t≠0, so the induced field is not conservative: its loop integral is the emf. And the induced field reaches outside the region of changing B→, as round a solenoid.

    Why people get this wrong: Thinking "no B at the wire, so no emf": the field outside a long solenoid is zero but the induced E→ there is not.

  14. MCQExam level

    A 25 mH inductor carries 0.30 A when, at t=0, it is switched across an uncharged 4.0 μF capacitor (no resistance anywhere). The largest voltage the capacitor reaches is about
    1. 16.8 V
    2. 23.7 V
    3. 1.9 kV
    4. 3.8 mV
    Answer and solution

    Answer: B

    Energy is conserved as it moves from the inductor to the capacitor: 12LI02=12CVmax⁡2, so Vmax⁡=I0L/C=0.300.0254.0×10−6=0.30×79.1=23.7 V, reached a quarter period (π2LC=0.50 ms) later.

    Why people get this wrong: Dropping the 12 on one side of the energy balance gives 16.8 V; I0L/C and I0C/L fail a units check (only L/C is a resistance).

  15. MCQHard

    A square loop of side a, mass m and resistance R falls with its plane vertical, its lower edge entering a region of horizontal uniform field B (perpendicular to the loop) below a horizontal boundary. While it is partly inside, its speed approaches
    1. mgRB2a2
    2. mgRBa
    3. mgRB2a2
    4. it keeps accelerating at g
    Answer and solution

    Answer: A

    Only the lower edge is in the field, so ℰ=Bav and I=Bav/R. The upward force on that edge is BIa=B2a2v/R. It balances mg at v=mgR/(B2a2). (Once fully inside, the flux stops changing and it falls at g again.)
  16. NATHard

    In a betatron, electrons circle at a fixed radius while the magnetic field is ramped up. For this to work, the field at the orbit must be what fraction of the average field over the area inside the orbit? (Two decimal places.)
    Answer and solution

    Answer: 0.5 (±0.01)

    The induced field speeds the electron up: dpdt=eE=e2πrdΦdt=er2dB‾dt. To keep the radius fixed, p=eBorbitr, so dpdt=erdBorbitdt. Equating: Borbit=12B‾ (starting from zero).
  17. MSQHard

    An insulating disc, free to turn on an axle, has small charges glued round its rim. A coaxial coil at its centre carries a steady current, which is then switched off. Which are correct?
    1. The disc starts to rotate.
    2. This violates conservation of angular momentum.
    3. The electromagnetic field held angular momentum before the switch-off.
    4. The disc stays still because magnetic forces do no work.
    Answer and solution

    Answer: A, C

    The falling flux induces a circling electric field at the rim, which pushes the charges round: the disc turns (A). Angular momentum is conserved because the fields of the charges and the coil together carried angular momentum, which passes to the disc (C, so B is false). D is false: the push comes from the induced electric field, not from the magnetic force.
  18. NATHard

    A rectangular loop (20 cm parallel to a long straight wire, 10 cm perpendicular) lies in the wire's plane with its near side 10 cm from the wire. Their mutual inductance is ______ nH (to one decimal place).
    Answer and solution

    Answer: 27.7 nH (±0.3)

    Current I in the wire gives flux ∫dd+bμ0I2πsads=μ0Ia2πln⁡d+bd. M=(2×10−7)(0.20)ln⁡2≈2.77×10−8 H.
  19. MCQHard

    Two coupled coils carry currents I1 and I2. Why must M≤L1L2?
    1. Because M is measured in the same units as L.
    2. Because the stored energy 12L1I12+12L2I22+MI1I2 must be positive for every choice of currents.
    3. Because flux cannot exceed μ0 times current.
    4. Because M=(L1+L2)/2 at most.
    Answer and solution

    Answer: B

    The energy is a quadratic form in (I1,I2). It is non-negative for all currents only if its discriminant is not positive: M2≤L1L2. (Physically: no more flux can link coil 2 than coil 1 makes.)
  20. NATHard

    A 0.50 H inductor carrying 2.0 A is suddenly connected across a 5.0 Ω resistor. The time for its stored energy to fall to half is ______ ms (to one decimal place).
    Answer and solution

    Answer: 34.7 ms (±0.35)

    I=I0e−t/τ with τ=L/R=0.10 s, so U∝I2∝e−2t/τ. Half when 2t/τ=ln⁡2: t=τln⁡2/2=0.10×0.693/2≈0.0347 s.

    Why people get this wrong: Using τln⁡2=69.3 ms, which is when the current halves.

  21. MCQHard

    Two coils with self-inductances L1 and L2 and mutual inductance M are connected in parallel, wound so that their fluxes aid. The equivalent inductance is (neglect resistance)
    1. L1L2−M2L1+L2+2M
    2. L1L2L1+L2+M
    3. L1L2−M2L1+L2−2M
    4. L1+L2+2M
    Answer and solution

    Answer: C

    Same voltage across both: V=L1I˙1+MI˙2=MI˙1+L2I˙2. Solving, I˙1=V(L2−M)L1L2−M2 and I˙2=V(L1−M)L1L2−M2. Adding: I˙=V(L1+L2−2M)L1L2−M2, so Leq=L1L2−M2L1+L2−2M. Check: M=0 gives the usual parallel rule.

    Why people get this wrong: Putting +2M in the denominator by analogy with the series-aiding rule L1+L2+2M; in parallel the signs come out the other way.

  22. MCQHard

    A superconducting ring (zero resistance, self-inductance L) carries no current. A magnet is then brought up so that it alone would put a flux Φext through the ring. Afterwards the current in the ring is
    1. Φext/L, set up so the ring's own flux adds to the magnet's
    2. zero, since no battery is connected
    3. a current that grows without limit
    4. Φext/L, set up so the ring's own flux cancels the magnet's
    Answer and solution

    Answer: D

    Around the ring IR=−dΦtotaldt with R=0, so the total flux Φext+LI cannot change. It started at zero, so LI=−Φext: a current of size Φext/L whose flux exactly cancels the magnet's, and it stays as long as the magnet stays.

    Why people get this wrong: Thinking a superconductor makes the induced current infinite; zero resistance fixes the flux, which keeps the current finite.

  23. NATHard

    Two long parallel wires, each of radius 1.0 mm and 10 cm apart (centre to centre), carry a current out along one and back along the other. Ignoring the flux inside the wires themselves, the self-inductance per metre of the pair is ______ μH/m (to two decimal places).
    Answer and solution

    Answer: 1.84 $\mu$H/m (±0.01)

    Between the wires, at distance x from one, both wires give fields in the same direction: B=μ0I2π(1x+1d−x). Flux per metre between the surfaces: ∫ad−aBdx=μ0Iπln⁡d−aa. So L/ℓ=μ0πln⁡d−aa=(4×10−7)ln⁡99=1.84μH/m (using ln⁡(d/a)=ln⁡100 gives the same to this precision).

    Why people get this wrong: Counting only one wire's field (half the answer).

  24. NATHard

    A 12 V battery is switched at t=0 onto a 20 Ω resistor in series with a 0.50 H ideal inductor. The rate at which energy is being stored in the inductor's magnetic field is largest at t= ______ ms (to two decimal places).
    Answer and solution

    Answer: 17.33 ms (±0.05)

    I=I0(1−e−t/τ) with τ=L/R=25 ms. The power into the inductor is PL=LIdIdt=LI02τ(1−e−t/τ)e−t/τ. With x=e−t/τ this is ∝x(1−x), largest at x=12: t=τln⁡2=25×0.693=17.33 ms. At that moment PL=V24R=1.8 W, the same as the power heating the resistor.

    Why people get this wrong: Choosing t=0 (largest dI/dt, but zero current) or t=τ; the product IdI/dt peaks in between.

  25. MSQHard

    A rod of mass m and length L slides without friction on horizontal rails in a vertical uniform field B. The rails are joined by an ideal capacitor C (no resistance), and a constant force F pulls the rod from rest. Which statements are correct?
    1. The current in the circuit is constant.
    2. The rod approaches a terminal speed, as it would with a resistor.
    3. The rod moves as if its mass were increased by B2L2C.
    4. The rod's acceleration is constant.
    Answer and solution

    Answer: A, C, D

    The capacitor voltage equals the emf: q=CBLv, so I=dq/dt=CBLa. The magnetic force on the rod is BIL=B2L2Ca, opposing the pull: F−B2L2Ca=ma, so a=Fm+B2L2C, a constant. Then I=CBLa is constant too, and the speed grows without limit. The term B2L2C acts as extra inertia: energy goes into both kinetic energy and the capacitor's field.

    Why people get this wrong: Carrying over the resistor result (terminal speed FR/B2L2): with a capacitor the opposing force depends on the acceleration, not the speed.

  26. MCQHard

    In the rod-and-capacitor set-up (rod on frictionless horizontal rails in a vertical field, rails joined by a capacitor, no resistance), m=0.10 kg, B=1.0 T, rail spacing L=0.50 m, C=0.20 F and a constant 0.30 N pull acts from rest. The rod's acceleration is
    1. 3.0 m/s2
    2. 6.0 m/s2
    3. 1.5 m/s2
    4. 2.0 m/s2
    Answer and solution

    Answer: D

    B2L2C=(1.0)2(0.50)2(0.20)=0.050 kg. a=Fm+B2L2C=0.300.10+0.050=2.0 m/s2. The capacitor current is CBLa=(0.20)(1.0)(0.50)(2.0)=0.20 A, steady.

    Why people get this wrong: 3.0 m/s2 ignores the induced current; 6.0 divides by B2L2C alone.

  27. NATTop rank

    A rod of mass 0.10 kg and length 0.50 m on frictionless horizontal rails is pulled by a constant 0.70 N force through a vertical 1.0 T field. The rails are joined by a 1.0 F capacitor (no resistance). The rod's acceleration is ______ m/s2 (to two decimal places).
    Answer and solution

    Answer: 2 m/s$^2$ (±0.02)

    The capacitor voltage follows the EMF: Q=CBLv, so I=CBLa. The magnetic force BIL=CB2L2a opposes F: F−CB2L2a=ma, giving a=Fm+CB2L2=0.700.10+0.25=2.0 m/s2, constant. The capacitor acts like extra mass.

    Why people get this wrong: Expecting a terminal speed as with a resistor.

  28. MSQTop rank

    A rod of mass m on horizontal frictionless rails closed by a resistor R, in a vertical field B, is given a speed v0 and left alone. Which are correct?
    1. It travels a total distance mv0R/(B2L2).
    2. Its speed decays exponentially with time.
    3. The total heat produced is 12mv02.
    4. Its speed decays exponentially with distance.
    Answer and solution

    Answer: A, B, C

    mdvdt=−B2L2Rv gives v=v0e−t/τ with τ=mR/(B2L2) (B). Writing dvdt=vdvdx: dvdx=−B2L2mR, a constant, so v falls linearly with distance (D false) and stops after x=mv0R/(B2L2) (A). All the kinetic energy becomes heat (C).

    Why people get this wrong: D: exponential in time, but linear in distance.

  29. NATTop rank

    For the coasting rod (previous idea): m=0.20 kg, v0=4.0 m/s, R=2.0 Ω, B=0.50 T, L=1.0 m. The total distance it travels is ______ m (to one decimal place).
    Answer and solution

    Answer: 6.4 m (±0.06)

    x=mv0RB2L2=(0.20)(4.0)(2.0)(0.25)(1.0)=6.4 m. (Its total time is infinite, but the distance is finite.)
  30. MCQTop rank

    A small loop of radius a is coaxial with a large loop of radius b≫a, a distance z away along the axis. Their mutual inductance is approximately
    1. μ0πa2b22(b2+z2)3/2
    2. μ0πab2b2+z2
    3. μ0πa22b for every z
    4. μ0a2b24π(b2+z2)3/2
    Answer and solution

    Answer: A

    Send current I round the big loop. Its axial field μ0Ib22(b2+z2)3/2 is nearly uniform over the small loop, so the flux is that times πa2. Divide by I. Check: at z=0 it gives μ0πa2/(2b), the flux through a small loop at the centre. By M12=M21 this also gives the much harder flux of the small loop's dipole field through the big loop.

← All topics · Timed mock test →