Waveguides, transmission lines, cavities and optical fibres
Electricity and magnetism · 90 questions and templates for GATE Physics, in order from warm-up to top rank. Check each answer, then read the full solution.
New to this topic? Read the lesson first: Waveguides.
Loading questions… (they need JavaScript; nothing you type is sent anywhere)
Written questions with solutions
The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.
-
MCQWarm-up
Which kind of wave can a hollow, perfectly conducting rectangular waveguide NOT carry?- TE
- TM
- TEM
- TE
Answer and solution
Answer: C
A TEM mode would need a transverse field that is both curl-free and divergence-free in the cross-section, i.e. a 2D electrostatic field inside a single closed conductor. That conductor is an equipotential, so the field is zero. TEM needs two separate conductors (coax, parallel plates).Why people get this wrong: The coaxial line, not the hollow guide, carries TEM.
-
MCQWarm-up
The dominant mode (lowest cutoff) of a hollow rectangular guide with broad side and narrow side is- TM
- TE
- TE
- TM
Answer and solution
Answer: B
is smallest for when : . TM modes need , so TM is higher and TM does not exist.Why people get this wrong: TE has cutoff , higher because .
-
NATWarm-up
An air-filled rectangular guide has inner dimensions 2.5 cm by 1.0 cm. The cutoff frequency of its TE mode is ______ GHz (to two decimal places).Answer and solution
Answer: 6 GHz (±0.03)
GHz. The cutoff wavelength is cm: half a wavelength must fit across the broad side.Why people get this wrong: Using the narrow side gives 15 GHz, the TE cutoff.
-
MCQWarm-up
A mode is driven at a frequency below its cutoff frequency. Along the guide its fields- travel with phase velocity below
- travel with group velocity above
- stay constant in amplitude
- decay exponentially without travelling (an evanescent mode)
Answer and solution
Answer: D
below cutoff, so and the fields go as with no travelling phase. In a lossless guide this is reactive: no power is absorbed, it is reflected back.Why people get this wrong: Below cutoff there is no propagation at any speed.
-
MCQWarm-up
Which of these modes does NOT exist in a rectangular waveguide?- TE
- TE
- TM
- TE
Answer and solution
Answer: C
TM modes have (it must vanish on all four walls). With this is identically zero, and with and there is no field at all. TE modes have , which allows one index to be zero.Why people get this wrong: TE can have one zero index; TM cannot have any.
-
MCQWarm-up
The cutoff wavelength of the TE mode of a rectangular guide of broad side isAnswer and solution
Answer: B
. The field is half a wavelength of the transverse standing wave across the broad side.Why people get this wrong: is the TE cutoff wavelength.
-
MCQWarm-up
As a filter for signals, a hollow metal waveguide behaves as a- low-pass filter
- band-stop filter
- high-pass filter
- all-pass filter (every frequency gets through)
Answer and solution
Answer: C
Every mode of a hollow guide has a cutoff frequency; below the lowest cutoff (that of the dominant mode) nothing propagates and fields die away exponentially. Above it signals pass. So the guide passes high frequencies and blocks low ones. (Higher modes join in at higher frequencies, which limits the useful single-mode band, but they do not block anything.)Why people get this wrong: A hollow pipe cannot carry a TEM wave, so unlike a coaxial cable it carries nothing at low frequency, not even dc.
-
NATStandard
A 10 GHz signal travels in the TE mode of an air-filled guide whose TE cutoff is 5 GHz. The guide wavelength is ______ cm (to two decimal places; take m/s).Answer and solution
Answer: 3.46 cm (±0.02)
cm. cm, longer than in free space.Why people get this wrong: The guide wavelength is longer than , not shorter.
-
NATStandard
A 9.0 GHz signal travels in the TE mode of an air-filled guide with cm. Its group velocity is ______ m/s (to two decimal places).Answer and solution
Answer: 2.24 ×10⁸ m/s (±0.02)
GHz. m/s.Why people get this wrong: The phase velocity m/s exceeds ; the group velocity, which carries energy, does not.
-
MSQStandard
For a propagating mode in a hollow, air-filled waveguide, which statements are true?- The phase velocity exceeds
- The group velocity is less than
- The product of phase and group velocities is
- The phase velocity tends to zero as
Answer and solution
Answer: A, B, C
(the same form as a plasma), so , and . As , and .Why people get this wrong: At cutoff it is the group velocity that vanishes; the phase velocity blows up.
-
NATStandard
An air-filled guide is 2.5 cm by 1.0 cm. Only the TE mode propagates from 6.0 GHz up to the next cutoff. That upper frequency is ______ GHz (to one decimal place).Answer and solution
Answer: 12 GHz (±0.06)
Next candidates: TE at GHz and TE at GHz. The lower, 12.0 GHz, ends the single-mode band. Choosing makes TE and TE arrive together and gives the widest single-mode octave.Why people get this wrong: Checking only TE misses TE, which comes first when .
-
MCQStandard
For the TE mode of a rectangular guide ( across the broad side, ), the electric field is- along , varying as
- along , largest at the walls
- along , varying as
- along , varying as and uniform in
Answer and solution
Answer: D
TE has , and from it , , with no dependence. is parallel to the side walls and vanishes there, as a tangential must; it is largest in the centre.Why people get this wrong: The index 1 counts half-waves along ; the field points along .
-
MCQStandard
The wave impedance of a TE mode in an air-filled guide at frequency above its cutoff isAnswer and solution
Answer: B
For TE modes , larger than . For TM modes , smaller.Why people get this wrong: TE and TM impedances are swapped forms; TE goes to infinity at cutoff.
-
NATStandard
A guide with cm is completely filled with polyethylene (). Its TE cutoff frequency is ______ GHz (to two decimal places).Answer and solution
Answer: 4 GHz (±0.02)
In the filling the wave speed is , so GHz. The cutoff wavelength in vacuum terms grows by .Why people get this wrong: Dividing by rather than its square root.
-
MCQStandard
Which structure can carry a wave with zero cutoff frequency?- A hollow rectangular guide
- A hollow circular guide
- A coaxial line
- A hollow guide filled with dielectric
Answer and solution
Answer: C
A coaxial line has two conductors, so it supports a TEM mode whose transverse field is the 2D electrostatic field between them; TEM has at every frequency, no cutoff. Hollow guides (filled or not) have one conductor and only TE and TM modes with non-zero cutoffs.Why people get this wrong: A dielectric filling lowers the cutoff but never to zero.
-
NATStandard
A coaxial cable has a ratio of outer to inner conductor radii of 3.6 and a polyethylene filling (). Its characteristic impedance is ______ (to one decimal place).Answer and solution
Answer: 51.2 Ω (±0.3)
and , so .Why people get this wrong: Use the natural logarithm, not .
-
MSQStandard
For a step-index optical fibre with core index and cladding index , in air, which statements are true?- The numerical aperture is
- The largest acceptance half-angle in air satisfies
- A larger core radius allows more guided modes
- The fibre is single-mode when
Answer and solution
Answer: A, B, C
The steepest guided ray meets the core-cladding wall at , so it makes with the axis. Snell at the end face: . The number of modes grows with . Single-mode operation needs (the first zero of ).Why people get this wrong: Single mode is for small , below 2.405.
-
NATStandard
A step-index fibre has core index 1.48 and cladding index 1.46. Its numerical aperture is ______ (to three decimal places).Answer and solution
Answer: 0.242 (±0.002)
, an acceptance half-angle of in air.Why people get this wrong: is not the numerical aperture.
-
MCQStandard
A 75 antenna is connected to a lossless 50 line. The voltage standing-wave ratio on the line is- 1.2
- 1.5
- 2.0
- 3.0
Answer and solution
Answer: B
, and . The reflected power fraction is .Why people get this wrong: 1.2 is , not the VSWR.
-
MCQStandard
An air-filled guide is completely filled with a dielectric of . Every mode's cutoff frequency is- doubled
- unchanged
- quartered
- halved
Answer and solution
Answer: D
, so it is halved. That is how dielectric-loaded guides are made smaller for the same band.Why people get this wrong: The cutoff goes as , not .
-
MCQStandard
As the operating frequency rises far above a mode's cutoff, its guide wavelength- grows without limit
- tends to
- approaches the free-space wavelength
- tends to zero faster than
Answer and solution
Answer: C
as : the bouncing plane waves travel almost along the axis, and the guide hardly matters.Why people get this wrong: grows without limit near cutoff, not far above it.
-
NATStandard
Two wide parallel metal plates cm apart have the space between them filled with a lossless dielectric of . The cutoff frequency of their TE mode is ______ GHz (to two decimal places).Answer and solution
Answer: 7.49 GHz (±0.03)
For plates a distance apart, mode needs half-wavelengths across the gap: with in the filling. GHz, half the air-filled value. The TEM mode still has no cutoff.Why people get this wrong: Forgetting that the filling slows the wave, or dividing by instead of .
-
MCQStandard
A lossless transmission line of characteristic impedance is terminated in a resistor equal to . Its input impedance is- , whatever the length of the line
- zero when the line is a quarter wavelength long
- infinite when the line is half a wavelength long
- only when the length is a whole number of half wavelengths
Answer and solution
Answer: A
A matched load absorbs the incident wave completely, so the reflection coefficient is . With no reflected wave, at every point on the line, so the input impedance is at any length. The standing-wave ratio is 1.Why people get this wrong: The "half-wavelength repeats the load" rule is true, but with a matched load every length repeats it.
-
NATExam level
How many distinct modes (counting TE and TM separately) can propagate at 20 GHz in an air-filled guide of 2.5 cm by 1.0 cm?Answer and solution
Answer: 8
GHz. With : TE, TE, TE (6, 12, 18 GHz). With : TE (15.0), TE and TM (16.2), TE and TM (19.2); gives 23.4 GHz. starts at 30 GHz. Total 8.Why people get this wrong: For each cutoff carries two modes, TE and TM.
-
NATExam level
A 3.0 GHz signal is fed into a 5.0 cm length of air-filled guide with cm (TE cutoff 6.0 GHz). By how many decibels is the field attenuated over this length? (to one decimal place)Answer and solution
Answer: 47.3 dB (±0.3)
with m and m: Np/m. Over 5 cm, Np, i.e. dB. A short length of below-cutoff guide is a strong, frequency-insensitive attenuator.Why people get this wrong: Far below cutoff , nearly independent of frequency.
-
MCQExam level
The TE mode can be built from two plane waves bouncing between the side walls and . Each makes an angle with the guide axis given byAnswer and solution
Answer: C
The two waves have and must form the standing wave , so , i.e. . At cutoff () : the waves bounce straight across and go nowhere. gives and .Why people get this wrong: Measured from the axis, grows towards at cutoff.
-
NATExam level
For the air-filled 2.5 cm by 1.0 cm guide, the cutoff frequency of the lowest TM mode is ______ GHz (to one decimal place).Answer and solution
Answer: 16.2 GHz (±0.08)
The lowest TM mode is TM: GHz.Why people get this wrong: TM and TM do not exist.
-
MSQExam level
For propagating modes in an air-filled hollow guide, which statements about the wave impedances are true?- Both tend to as
- grows without limit as
Answer and solution
Answer: A, B, C
and . Far above cutoff both tend to . At cutoff and ; also at the same .Why people get this wrong: It is that diverges at cutoff.
-
NATExam level
An air-filled circular guide has inner radius 1.0 cm. Its dominant TE mode, with (first zero of ), has cutoff frequency ______ GHz (to two decimal places).Answer and solution
Answer: 8.78 GHz (±0.04)
, so GHz. Its cutoff wavelength is .Why people get this wrong: TE modes use zeros of ; TM modes use zeros of .
-
MCQExam level
In a circular guide, the ratio of the TM cutoff (first zero of : 2.405) to the TE cutoff (first zero of : 1.841) is closest to- 1.31
- 0.77
- 1.00
- 2.08
Answer and solution
Answer: A
Cutoff frequencies scale as the Bessel zeros: . So TE is dominant, and the single-mode band of a circular guide spans only a factor 1.31, narrower than a rectangular guide's factor 2.Why people get this wrong: Inverting the ratio gives 0.77, which would make TM dominant.