Home / Courses / IIT JAM Physics / Practice / DC transients and AC circuits

DC transients and AC circuits

Electricity and magnetism · 79 questions and templates for IIT JAM Physics, in order from warm-up to top rank. Check each answer, then read the full solution.

New to this topic? Read the lesson first: DC transients and AC circuits.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. NATWarm-up

    A 100μF capacitor charges through a 10 kΩ resistor. The time constant is ______ s.
    Answer and solution

    Answer: 1 s (±0.01)

    τ=RC=(10×103)(100×10−6)=1.0 s. After one time constant a charging capacitor reaches 63% of its final voltage.

    Why people get this wrong: Using 10 instead of 104 for kΩ, or 10−4 wrongly for μF (10−6).

  2. MCQWarm-up

    The reactance of a 0.10 H inductor at 50 Hz is about
    1. 5 Ω
    2. 31.4 Ω
    3. 0.032 Ω
    4. 314 Ω
    Answer and solution

    Answer: B

    XL=ωL=2πfL=2π(50)(0.10)=31.4 Ω.

    Why people get this wrong: Using f instead of ω=2πf gives 5 Ω.

  3. MCQWarm-up

    In an AC circuit containing only a capacitor, the current
    1. is in phase with the voltage
    2. lags the voltage by 90∘
    3. leads the voltage by 45∘
    4. leads the voltage by 90∘
    Answer and solution

    Answer: D

    q=CV0sin⁡ωt so I=dq/dt=ωCV0cos⁡ωt=ωCV0sin⁡(ωt+90∘). The current peaks a quarter cycle before the voltage: it leads by 90∘. (Memory aid: "ICE": in a capacitor, I before E.)

    Why people get this wrong: Lagging by 90∘ is the inductor.

  4. MSQWarm-up

    A series LCR circuit is driven at its resonant frequency. Which statements are correct?
    1. Its impedance is at its minimum, equal to R.
    2. The current is in phase with the source voltage.
    3. The voltages across L and C are equal in size and opposite in phase.
    4. The power factor is zero.
    Answer and solution

    Answer: A, B, C

    At ω0=1/LC, XL=XC, so Z=R2+(XL−XC)2=R is smallest, and the phase tan⁡ϕ=(XL−XC)/R=0. VL and VC are equal and 180∘ apart, so they cancel. Power factor cos⁡ϕ=1, the largest possible.

    Why people get this wrong: Zero power factor belongs to a pure L or pure C, not to resonance.

  5. NATWarm-up

    A sinusoidal mains voltage has a peak value of 311 V. Its rms value is ______ V (to the nearest whole number).
    Answer and solution

    Answer: 220 V (±1)

    For a sine wave, Vrms=V0/2=311/1.414=220 V. The rms value is the steady DC voltage that would heat a resistor equally.

    Why people get this wrong: The average of a full sine wave is zero; the average of its magnitude is 2V0/π=198 V, which is not the rms.

  6. MCQWarm-up

    A capacitor charges from zero through a resistor from a battery. After one time constant its voltage is about what fraction of the battery voltage?
    1. 37%
    2. 50%
    3. 63%
    4. 86%
    Answer and solution

    Answer: C

    V=V0(1−e−t/τ); at t=τ, 1−e−1=0.632. After 2τ it is 86%, after 5τ more than 99%.

    Why people get this wrong: 37% is what is left of a discharging capacitor after one τ.

  7. MCQWarm-up

    Kirchhoff's loop rule (the sum of potential changes around any closed loop is zero) rests on
    1. conservation of charge
    2. Ohm's law
    3. Lenz's law
    4. the electrostatic field being conservative, so the work around a closed path is zero
    Answer and solution

    Answer: D

    Going round a loop and back to the start, the potential must return to its starting value; that is true because a static (or slowly varying) electric field is conservative, ∮E→⋅dl→=0, which is energy conservation for a test charge. The junction rule is the one that rests on charge conservation.

    Why people get this wrong: Swapping the two rules: junction rule = charge, loop rule = energy.

  8. NATStandard

    A 10 mH inductor and a 1.0μF capacitor are in series with a small resistor. The resonant frequency is ______ Hz (to the nearest whole number).
    Answer and solution

    Answer: 1592 Hz (±16)

    f0=12πLC=12π10−2×10−6=12π×10−4=1592 Hz.

    Why people get this wrong: 1/LC=104 is ω0 in rad/s; divide by 2π for hertz.

  9. MCQStandard

    A coil of resistance 30 Ω and reactance 40 Ω is connected to an AC supply. Its power factor is
    1. 0.75
    2. 0.8
    3. 0.6
    4. 1.33
    Answer and solution

    Answer: C

    Z=302+402=50 Ω. Power factor cos⁡ϕ=R/Z=30/50=0.6.

    Why people get this wrong: 0.8 is X/Z, which is sin⁡ϕ.

  10. MCQStandard

    A series circuit has R=30 Ω, XL=80 Ω and XC=40 Ω. Its impedance is
    1. 50 Ω
    2. 150 Ω
    3. 96 Ω
    4. 70 Ω
    Answer and solution

    Answer: A

    Inductive and capacitive reactances subtract (their voltages are 180∘ apart): Z=R2+(XL−XC)2=900+1600=50 Ω.

    Why people get this wrong: Adding all three (150) or adding the reactances in quadrature (96).

  11. MCQStandard

    A capacitor discharges through a resistor. The time for its voltage to fall to half is
    1. τ/2
    2. τln⁡2
    3. τ
    4. 2τ
    Answer and solution

    Answer: B

    V=V0e−t/τ=V0/2 gives t=τln⁡2=0.693τ. The stored energy (∝V2) halves sooner, at 12τln⁡2.

    Why people get this wrong: Thinking half-life equals the time constant.

  12. NATStandard

    A 2.0μF capacitor is charged from zero to 100 V through a 1 kΩ resistor by a 100 V battery. The heat produced in the resistor is ______ mJ.
    Answer and solution

    Answer: 10 mJ (±0.1)

    The battery delivers QV=CV2=20 mJ. The capacitor stores 12CV2=10 mJ. The rest, 10 mJ, is heat in the resistor, whatever its resistance: ∫I2Rdt=∫0∞V2Re−2t/RCdt=12CV2.

    Why people get this wrong: Expecting a smaller resistor to waste less. It carries a bigger current for a shorter time and wastes exactly the same.

  13. MSQStandard

    A battery V is switched on at t=0 to a resistor R and an inductor L in series. Which statements are correct?
    1. The current is zero just after the switch closes.
    2. Just after the switch closes, the voltage across the inductor equals V.
    3. After a long time the inductor behaves like a plain wire.
    4. The time constant is RL.
    Answer and solution

    Answer: A, B, C

    An inductor resists sudden changes of current, so I(0+)=0; then there is no drop across R, and the whole V appears across L. As I→V/R, dI/dt→0 and the inductor's voltage vanishes: it is a short circuit. The time constant is L/R (henry per ohm = seconds).

    Why people get this wrong: RL has units of Ω H, not seconds. RC for capacitors, L/R for inductors.

  14. MCQStandard

    The average power delivered to a circuit by a sinusoidal source with rms voltage V and rms current I, the current lagging by ϕ, is
    1. VI
    2. VIsin⁡ϕ
    3. 12VIcos⁡ϕ
    4. VIcos⁡ϕ
    Answer and solution

    Answer: D

    Instantaneous power is v(t)i(t). Averaging 2Vsin⁡ωt⋅2Isin⁡(ωt−ϕ) over a cycle gives VIcos⁡ϕ. With peak values it would be 12V0I0cos⁡ϕ.

    Why people get this wrong: The 12 appears only with peak values, not rms values.

  15. NATStandard

    A series LCR circuit has R=10 Ω, L=0.10 H and C=10μF. Its quality factor is ______.
    Answer and solution

    Answer: 10 (±0.05)

    Q=ω0LR=1RLC=1100.1010−5=10010=10.

    Why people get this wrong: Inverting the square root: it is L/C, which has units of ohms.

  16. MCQStandard

    In an ideal LC circuit the charge oscillates at angular frequency ω0. The energy stored in the capacitor oscillates at
    1. ω0/2
    2. ω0
    3. 2ω0
    4. 4ω0
    Answer and solution

    Answer: C

    UC=q22C=Q022Ccos2⁡ω0t=Q024C(1+cos⁡2ω0t). It peaks twice per cycle of charge (at q=+Q0 and q=−Q0).

    Why people get this wrong: Energy depends on q2, so it ignores the sign of the charge and repeats twice as often.

  17. NATStandard

    A series LCR circuit has R=20 Ω and L=0.50 H. Its half-power bandwidth is ______ Hz (to two decimal places).
    Answer and solution

    Answer: 6.37 Hz (±0.06)

    The half-power points are separated by Δω=R/L=40 rad/s, independent of C. In hertz: Δf=402π=6.37 Hz.

    Why people get this wrong: Giving 40: that is in rad/s.

  18. MCQStandard

    A 12 V ideal battery drives two 4 Ω resistors in series. Seen from the two ends of the second resistor, the circuit's Thevenin equivalent is
    1. 6 V in series with 2 Ω
    2. 12 V in series with 8 Ω
    3. 6 V in series with 4 Ω
    4. 12 V in series with 2 Ω
    Answer and solution

    Answer: A

    Open-circuit voltage: the divider gives 12×44+4=6 V. Thevenin resistance: replace the battery by a wire, so the two resistors appear in parallel between the terminals: 4∥4=2 Ω.

    Why people get this wrong: Adding the resistors in series for Rth; with the source shorted they are in parallel.

  19. NATExam level

    A 12 V battery charges an uncharged capacitor through a 4.0 kΩ resistor. One time constant after the switch closes, the current is ______ mA (to two decimal places).
    Answer and solution

    Answer: 1.1 mA (±0.01)

    The charging current is I=VRe−t/τ, starting at 12/4000=3.0 mA. At t=τ: 3.0×e−1=3.0×0.368=1.10 mA.

    Why people get this wrong: Using (1−e−1) for the current. Voltage on the capacitor rises like that; current falls.

  20. MCQExam level

    A charged capacitor discharges through a series inductor and resistor. The charge returns to zero fastest without oscillating when
    1. R=L/C
    2. R=2L/C
    3. R=12L/C
    4. R=0
    Answer and solution

    Answer: B

    Lq¨+Rq˙+q/C=0 has roots s=−R2L±R24L2−1LC. Critical damping, where the square root vanishes, is R=2L/C. Less resistance oscillates; more creeps back slowly.

    Why people get this wrong: L/C without the 2 is the characteristic impedance, not the critical resistance.

  21. NATExam level

    For a series circuit with L=0.20 H and C=5.0μF, the resistance for critical damping is ______ Ω.
    Answer and solution

    Answer: 400 $\Omega$ (±1)

    Rc=2L/C=20.20/(5.0×10−6)=24×104=400 Ω.

    Why people get this wrong: Forgetting the factor 2 gives 200 Ω.

  22. MSQExam level

    Which statements about the free (undriven) series LCR circuit are correct?
    1. It oscillates if R<2L/C.
    2. When it oscillates, the angular frequency is 1LC−R24L2.
    3. When critically damped, the charge returns to zero fastest without overshooting.
    4. When overdamped, it oscillates with a decaying amplitude.
    Answer and solution

    Answer: A, B, C

    The characteristic roots are complex when R2/4L2<1/LC, i.e. R<2L/C, giving decaying oscillations at ωd=ω02−(R/2L)2. At equality the response is critical: quickest return without overshoot. Above it (overdamped) both roots are real and negative: no oscillation, just a slow decay.

    Why people get this wrong: Overdamped means too much damping to oscillate at all.

  23. NATExam level

    A series LCR circuit with R=100 Ω is connected to a 200 V rms supply at a frequency where XL−XC=100 Ω. The average power drawn is ______ W.
    Answer and solution

    Answer: 200 W (±1)

    Z=1002+1002=141.4 Ω, Irms=200/141.4=1.414 A. Only the resistor absorbs power: P=I2R=2.0×100=200 W. (Equivalently VIcos⁡ϕ=200×1.414×0.707.) At resonance it would be 400 W: here we sit at a half-power point.

    Why people get this wrong: Computing V2/R=400 W, which holds only at resonance.

  24. MCQExam level

    At resonance, the rms voltage across the capacitor of a series LCR circuit (quality factor Q) driven by a source of rms voltage V is
    1. V/Q
    2. V
    3. zero, since it cancels the inductor
    4. QV
    Answer and solution

    Answer: D

    At resonance I=V/R, so VC=IXC=VR⋅1ω0C=V⋅1ω0RC=QV. With Q=50, a 2 V source puts 100 V across the capacitor, which is why radio tuning circuits magnify weak signals (and why components must be rated for it).

    Why people get this wrong: The L and C voltages cancel each other, but each one alone is Q times the source.

  25. MCQExam level

    A 10 V source with internal resistance 5 Ω feeds a variable load resistor. The largest power the load can draw is
    1. 20 W
    2. 10 W
    3. 5 W
    4. 2.5 W
    Answer and solution

    Answer: C

    P=V2RL(RL+r)2 is greatest when RL=r=5 Ω. Then I=1 A and P=I2RL=5 W =V2/(4r). The source wastes another 5 W inside, so efficiency is only 50%.

    Why people get this wrong: 20 W is V2/r, the power wasted if the terminals are shorted.

  26. MCQExam level

    An ideal inductor and an ideal capacitor are connected in parallel across an AC source at their resonant frequency 1/LC. The current drawn from the source is
    1. zero, because the impedance is infinite
    2. very large, because the impedance is zero
    3. the same as through the inductor alone
    4. twice the current through the capacitor
    Answer and solution

    Answer: A

    In parallel each branch gets the full source voltage. The inductor current lags by 90∘ and the capacitor current leads by 90∘; at resonance they are equal and cancel. The source supplies nothing while a large current circulates round the LC loop. Real coils have resistance, so the line current is small, not zero.

    Why people get this wrong: Series resonance gives minimum impedance; parallel resonance gives maximum.

  27. NATExam level

    A 10μF capacitor charged to 10 V discharges through a 2.0 kΩ and a 3.0 kΩ resistor connected in parallel with each other. The time constant is ______ ms.
    Answer and solution

    Answer: 12 ms (±0.1)

    The capacitor sees the two resistors in parallel: R=2×32+3=1.2 kΩ. τ=RC=1200×10−5=12 ms.

    Why people get this wrong: Adding the resistors (50 ms). Ask which resistance the capacitor discharges through.

  28. MCQExam level

    A 100 Ω resistor and a capacitor of reactance 100 Ω are in series across an AC source. The current
    1. leads the source voltage by 45∘
    2. lags the source voltage by 45∘
    3. leads the source voltage by 90∘
    4. is in phase with the source voltage
    Answer and solution

    Answer: A

    Z=R−jXC=100−100j, of phase −45∘. The current I=V/Z has phase +45∘ relative to V: it leads. Capacitive circuits have leading currents.

    Why people get this wrong: Mixing up the sign: an RL circuit would have the current lagging.

  29. MSQExam level

    In a series LCR circuit the rms voltages are VR=30 V, VL=80 V and VC=40 V. Which statements are correct?
    1. The rms source voltage is 50 V.
    2. The circuit is inductive.
    3. The current lags the source voltage by about 53∘.
    4. The rms source voltage is the sum of the three rms voltages, 150 V.
    Answer and solution

    Answer: A, B, C

    Phasors: VR along the current, VL ahead by 90∘, VC behind by 90∘. V=302+(80−40)2=50 V. VL>VC, so the circuit is inductive and the current lags by tan−1⁡(40/30)=53.1∘. rms values of out-of-phase voltages do not add arithmetically.

    Why people get this wrong: The component voltages can each exceed the source voltage; only their phasor sum equals it.

  30. NATExam level

    A 10 V battery is switched on at t=0 to a 100 Ω resistor in series with a 0.50 H inductor. The current at t=10 ms is ______ mA (to one decimal place).
    Answer and solution

    Answer: 86.5 mA (±0.9)

    τ=L/R=5.0 ms and I∞=100 mA. I=100(1−e−10/5)=100(1−0.135)=86.5 mA.

    Why people get this wrong: Using τ=RL=50 s, which gives almost zero current.

← All topics · Timed mock test →