Home / Courses / IIT JAM Physics / Practice / Dielectrics and capacitors

Dielectrics and capacitors

Electricity and magnetism · 76 questions and templates for IIT JAM Physics, in order from warm-up to top rank. Check each answer, then read the full solution.

New to this topic? Read the lesson first: Dielectrics and capacitors.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. MCQWarm-up

    A parallel-plate capacitor stays connected to a battery while a dielectric of constant 4 is slid in to fill the gap. The charge on the plates
    1. stays the same
    2. becomes 4 times larger
    3. becomes 4 times smaller
    4. becomes 16 times larger
    Answer and solution

    Answer: B

    The battery holds V fixed. Filling the gap multiplies the capacitance by κ=4, so Q=CV becomes 4 times larger. The battery supplies the extra charge.

    Why people get this wrong: Mixing up the two cases: with the battery removed, Q stays fixed and V drops by 4 instead.

  2. NATWarm-up

    Two plates of area 0.020 m2 are 1.0 mm apart with a dielectric of constant 5.0 filling the gap. The capacitance is ______ pF (to the nearest whole number).
    Answer and solution

    Answer: 885 pF (±9)

    C=κϵ0Ad=5.0×8.854×10−12×0.0201.0×10−3=8.85×10−10 F =885 pF.

    Why people get this wrong: Forgetting to turn 1.0 mm into 10−3 m, which is off by a factor of 1000.

  3. MCQWarm-up

    The SI unit of the polarisation P→ (dipole moment per unit volume) is
    1. V/m
    2. C m
    3. C/m3
    4. C/m2
    Answer and solution

    Answer: D

    Dipole moment has units C m; per unit volume, (C m)/m3 = C/m2. It is the same unit as surface charge density, which is no accident: the bound surface charge is σb=P→⋅nˆ.

    Why people get this wrong: C m is the unit of a single dipole moment, not of the moment per volume.

  4. MSQWarm-up

    Which of these are correct for a linear, isotropic dielectric of permittivity ϵ=ϵ0ϵr?
    1. D→=ϵ0E→+P→
    2. D→=ϵE→
    3. P→=ϵ0χeE→ with χe=ϵr−1
    4. ∇⋅D→ equals the total (free plus bound) charge density
    Answer and solution

    Answer: A, B, C

    The first is the definition of D→, true in any material. For a linear isotropic material P→=ϵ0χeE→, so D→=ϵ0(1+χe)E→=ϵE→. The divergence of D→ is the free charge density only; that is the whole point of D→.

    Why people get this wrong: ∇⋅E→ is total charge over ϵ0; ∇⋅D→ is free charge.

  5. MCQWarm-up

    A charged parallel-plate capacitor is disconnected from its battery. A slab of dielectric constant κ is then slid in to fill the gap. The stored energy
    1. becomes κ times larger
    2. stays the same
    3. becomes κ times smaller
    4. becomes κ2 times smaller
    Answer and solution

    Answer: C

    Isolated: Q is fixed. U=Q2/(2C) and C grows by κ, so U falls by κ. The lost energy went into pulling the slab in (the capacitor does work on it).

    Why people get this wrong: Using U=12CV2 with V held fixed: that is the battery-connected case.

  6. NATWarm-up

    Capacitors of 3μF and 6μF are connected in series. The combined capacitance is ______ μF.
    Answer and solution

    Answer: 2 $\mu$F

    In series the charge is the same on each and the voltages add: 1C=13+16=12, so C=2μF, smaller than either.

    Why people get this wrong: Adding them (9 μF) is the parallel rule.

  7. NATStandard

    A dielectric cube of side 5.0 cm has uniform polarisation P→=2.0μC/m2zˆ, with two faces normal to z. The bound charge on the top face (the face with outward normal +zˆ) is ______ nC.
    Answer and solution

    Answer: 5 nC (±0.05)

    σb=P→⋅nˆ=+2.0μC/m2 on the top face. Charge =σbA=(2.0×10−6)(0.050)2=5.0×10−9 C =5.0 nC. The bottom face carries −5.0 nC, the side faces nothing (P→⋅nˆ=0), and inside ρb=−∇⋅P→=0.

    Why people get this wrong: Giving the side faces charge: only the component of P→ along the outward normal counts.

  8. MCQStandard

    A dielectric sphere has polarisation P→=krrˆ (k a constant). The bound volume charge density inside it is
    1. −3k
    2. 3k
    3. −k
    4. −2k/r
    Answer and solution

    Answer: A

    ρb=−∇⋅P→=−1r2ddr(r2⋅kr)=−1r2(3kr2)=−3k, uniform. The surface gets σb=P(R)=kR; total bound charge −3k⋅43πR3+kR⋅4πR2=0, as it must be.

    Why people get this wrong: Dropping the minus sign in ρb=−∇⋅P→, or using the Cartesian d/dr without the r2.

  9. MCQStandard

    A neutral piece of dielectric of any shape is polarised by an external field. The total bound charge (volume plus surface) on it is
    1. equal to ϵ0 times the flux of E→ through its surface
    2. zero
    3. equal to −∮P→⋅da→, which is not zero in general
    4. positive on the whole
    Answer and solution

    Answer: B

    Total bound charge =∫(−∇⋅P→)dτ+∮P→⋅da→=0 by the divergence theorem. Polarisation only shifts charges inside each molecule; it cannot create net charge.

    Why people get this wrong: The surface charge alone is ∮P→⋅da→, which can be non-zero, but the volume charge cancels it.

  10. NATStandard

    A parallel-plate capacitor has plates of area 0.010 m2 separated by 5.0 mm. A slab 2.0 mm thick with dielectric constant 4.0 is placed in the gap, parallel to the plates. The capacitance is ______ pF (to one decimal place).
    Answer and solution

    Answer: 25.3 pF (±0.3)

    The slab and the air are in series: C=ϵ0Ad−t+t/κ=8.854×10−12×0.0103.0×10−3+0.5×10−3=2.53×10−11 F =25.3 pF. Where the slab sits in the gap does not matter.

    Why people get this wrong: Multiplying the air-filled value by κ as if the slab filled the gap.

  11. MCQStandard

    The gap of a parallel-plate capacitor (plate area A, gap d) is filled with two dielectrics side by side, κ1 under one half of the plate area and κ2 under the other half. The capacitance is
    1. 2ϵ0Adκ1κ2κ1+κ2
    2. ϵ0Ad(κ1+κ2)
    3. ϵ0A2d(κ1+κ2)
    4. ϵ0Adκ1κ2
    Answer and solution

    Answer: C

    Side by side, both halves feel the same voltage, so they are in parallel: C=κ1ϵ0(A/2)d+κ2ϵ0(A/2)d=ϵ0A2d(κ1+κ2).

    Why people get this wrong: The first option is the series answer for two layers stacked one above the other.

  12. MCQStandard

    The energy stored in a 10μF capacitor charged to 50 V is
    1. 12.5 mJ
    2. 25 mJ
    3. 0.25 J
    4. 1.25 mJ
    Answer and solution

    Answer: A

    U=12CV2=12(10×10−6)(50)2=1.25×10−2 J =12.5 mJ.

    Why people get this wrong: Forgetting the 12 gives 25 mJ.

  13. MSQStandard

    At the flat boundary between two linear dielectrics with no free charge on it, which quantities are continuous?
    1. The component of E→ along the boundary
    2. The component of D→ normal to the boundary
    3. The component of E→ normal to the boundary
    4. The component of D→ along the boundary
    Answer and solution

    Answer: A, B

    ∇×E→=0 (a thin rectangular loop) makes E∥ continuous. ∇⋅D→=ρf=0 (a thin pillbox) makes D⟂ continuous. Then E⟂=D⟂/ϵ jumps by ϵ1/ϵ2, and D∥=ϵE∥ jumps too.

    Why people get this wrong: Bound charge sits on the boundary, so E⟂ jumps even with no free charge.

  14. MCQStandard

    A large slab of linear dielectric (constant κ) is placed in a uniform field E0 with its faces perpendicular to the field. The field inside the slab is
    1. E0/κ
    2. κE0
    3. E0
    4. E0(κ−1)/κ
    Answer and solution

    Answer: A

    With no free charge on the faces, D⟂ is continuous: ϵ0E0=κϵ0Ein, so Ein=E0/κ. The bound charges on the faces partly cancel the applied field.

    Why people get this wrong: This simple result needs the faces perpendicular to the field; a slab lying along the field has Ein=E0, and a sphere gets 3E0/(κ+2).

  15. MCQStandard

    A capacitor is charged to 100 V and disconnected. A dielectric of constant 2.5 is then slid in to fill the gap completely. The voltage across it becomes
    1. 250 V
    2. 100 V
    3. 40 V
    4. 16 V
    Answer and solution

    Answer: C

    Isolated, so Q is fixed; C grows by 2.5; V=Q/C falls to 100/2.5=40 V. The field in the gap also falls by 2.5.

    Why people get this wrong: 250 V comes from multiplying instead of dividing.

  16. MCQStandard

    A material has relative permittivity 3.5. Its electric susceptibility is
    1. 3.5
    2. 2.5
    3. 4.5
    4. 1/3.5
    Answer and solution

    Answer: B

    ϵr=1+χe, so χe=3.5−1=2.5. Vacuum has χe=0, ϵr=1.

    Why people get this wrong: Taking χe=ϵr.

  17. MCQStandard

    A very thin, isolated, uncharged metal foil is slid into a charged parallel-plate capacitor, parallel to the plates and halfway between them. The capacitance
    1. doubles
    2. halves
    3. stays the same
    4. becomes infinite
    Answer and solution

    Answer: C

    Charges ∓Q are induced on the two faces of the foil, so the field in each half-gap is unchanged (σ/ϵ0) and the field inside the foil (zero thickness) adds nothing. The voltage V=Ed is unchanged, so C=Q/V is unchanged. Equivalently, two capacitors of gap d/2 in series give 12(2C)=C.

    Why people get this wrong: Thinking of two capacitors in parallel (doubles), or forgetting that a foil of finite thickness t would raise C to ϵ0A/(d−t).

  18. MCQStandard

    Which of these holds in every material, whether or not it is linear?
    1. D→=εE→
    2. ∇×D→=0
    3. ∇⋅D→=ρfree
    4. P→=ε0χeE→
    Answer and solution

    Answer: C

    D→ is defined as ε0E→+P→; Gauss's law ∇⋅(ε0E→)=ρfree+ρb with ρb=−∇⋅P→ gives ∇⋅D→=ρfree always. D→=εE→ and P→=ε0χeE→ hold only for linear media. ∇×D→=∇×P→, which is non-zero for example at the edges of a uniformly polarised bar.

    Why people get this wrong: Assuming D→ behaves like E→ and has zero curl; it generally does not.

  19. NATStandard

    An air capacitor of 0.50 μF has its gap filled with mica (dielectric constant 6.0) and is then connected in series with an air capacitor of 1.0 μF. The combined capacitance is ______ μF.
    Answer and solution

    Answer: 0.75 μF (±0.005)

    Filling the gap multiplies the capacitance by κ: 0.50×6.0=3.0 μF. In series with 1.0 μF: 3.0×1.03.0+1.0=0.75 μF.

    Why people get this wrong: Adding series capacitances directly.

  20. NATExam level

    A spherical capacitor has an inner sphere of radius 5.0 cm and an outer shell of radius 10 cm, with vacuum between. Its capacitance is ______ pF (to two decimal places).
    Answer and solution

    Answer: 11.13 pF (±0.11)

    With ±Q on the spheres, V=kQ(1a−1b), so C=4πϵ0abb−a=(0.05)(0.10)(8.99×109)(0.05)=1.11×10−11 F =11.13 pF.

    Why people get this wrong: Using 4πϵ0a (the isolated sphere), which ignores the outer shell.

  21. NATExam level

    A coaxial cable has an inner conductor of radius 1.0 mm and an outer conductor of radius 5.0 mm, with polyethylene (κ=2.2) between. Its capacitance per metre is ______ pF/m (to one decimal place).
    Answer and solution

    Answer: 76 pF/m (±0.8)

    Gauss's law for D→ gives E=λ2πκϵ0s, so V=λ2πκϵ0ln⁡ba and Cl=2πκϵ0ln⁡(b/a)=2π(2.2)(8.854×10−12)ln⁡5=7.60×10−11 F/m.

    Why people get this wrong: Using log10⁡5 instead of ln⁡5.

  22. MCQExam level

    Field lines pass from a dielectric with ϵr1=2 into one with ϵr2=6 across a flat boundary carrying no free charge. In the first medium the field makes 30∘ with the normal. In the second it makes
    1. 10.9∘
    2. 30∘
    3. 45∘
    4. 60∘
    Answer and solution

    Answer: D

    E∥ continuous and ϵE⟂ continuous give tan⁡θ2tan⁡θ1=ϵ2ϵ1. So tan⁡θ2=3tan⁡30∘=3 and θ2=60∘. Lines bend away from the normal entering the higher-permittivity medium.

    Why people get this wrong: Using Snell's law with sines, or putting the ratio upside down (giving 10.9∘).

  23. MSQExam level

    A charged capacitor is isolated, and a dielectric slab (of the same thickness as the gap) is partly inserted between its plates, edge first. Neglect friction. Which statements are correct?
    1. The slab is pulled further in.
    2. The force on the slab is the same at every insertion depth.
    3. The stored energy decreases as the slab moves in.
    4. The voltage between the plates decreases as the slab moves in.
    Answer and solution

    Answer: A, C, D

    With Q fixed, U=Q2/(2C) and C(x) grows linearly with the inserted length x. The force F=−dU/dx=Q22C2dCdx is positive (inward) but falls as C grows, so it depends on x. U and V=Q/C both fall as the slab goes in.

    Why people get this wrong: With a battery connected the force is independent of x, since then F=12V2dC/dx with V fixed.

  24. NATExam level

    A parallel-plate capacitor has square plates 10 cm wide and a gap of 2.0 mm, and stays connected to a 200 V supply. A slab of dielectric constant 3.0 that just fits the gap is partly inserted. The force pulling it in is ______ μN (to one decimal place).
    Answer and solution

    Answer: 17.7 $\mu$N (±0.2)

    With inserted length x and plate width w: C=ϵ0wd[κx+(L−x)], so dCdx=ϵ0w(κ−1)d. At fixed V, F=12V2dCdx=ϵ0(κ−1)wV22d=(8.854×10−12)(2)(0.10)(4×104)4×10−3=1.77×10−5 N.

    Why people get this wrong: Using κ instead of κ−1: only the change in capacitance pulls.

  25. MCQExam level

    A capacitor connected to a battery has a dielectric slab pushed into it, raising its stored energy by ΔU. The work done by the battery in this process is
    1. ΔU
    2. zero
    3. ΔU/2
    4. 2ΔU
    Answer and solution

    Answer: D

    The battery moves extra charge ΔQ through voltage V: Wb=VΔQ=V2ΔC. The stored energy rises by 12V2ΔC=ΔU. So Wb=2ΔU; the other half is the work done on the slab as it is pulled in (or heat, if it slams in).

    Why people get this wrong: Assuming all the battery's work ends up stored.

  26. NATExam level

    A solid sphere of linear dielectric with ϵr=4 is placed in a uniform field of 300 V/m. The field inside the sphere is ______ V/m.
    Answer and solution

    Answer: 150 V/m

    Solving Laplace's equation inside and outside with the boundary conditions gives a uniform field inside: Ein=3ϵr+2E0=36(300)=150 V/m, along E0.

    Why people get this wrong: Using E0/ϵr=75 V/m, which is the slab result, not the sphere.

  27. MCQExam level

    The Clausius-Mossotti relation links the relative permittivity of a dense, non-polar medium to the polarisability α of its molecules (number density N). It reads
    1. ϵr−1=Nα/ϵ0
    2. ϵr−1ϵr+2=Nα3ϵ0
    3. ϵr+2ϵr−1=Nα3ϵ0
    4. ϵr=1+3Nα/ϵ0
    Answer and solution

    Answer: B

    Each molecule feels the local field E+P/(3ϵ0), not just E. With P=NαEloc and P=ϵ0(ϵr−1)E, eliminating Eloc gives ϵr−1ϵr+2=Nα3ϵ0. For dilute gases (ϵr≈1) it reduces to the first option.

    Why people get this wrong: The first option is only the dilute-gas limit; it ignores the field of neighbouring dipoles.

  28. NATExam level

    A 2.0μF capacitor charged to 100 V is connected across an uncharged 3.0μF capacitor. The energy lost in the process is ______ mJ.
    Answer and solution

    Answer: 6 mJ (±0.05)

    Initial energy 12(2×10−6)(100)2=10 mJ. Charge 200μC is shared at a common voltage V=200/5=40 V. Final energy 12(5×10−6)(40)2=4 mJ. Lost: 6 mJ, as heat in the wires and as radiation. In general the loss is C1C22(C1+C2)(V1−V2)2, whatever the resistance.

    Why people get this wrong: Assuming energy is conserved because charge is. It is not: there is always loss when capacitors at different voltages are joined.

  29. MSQExam level

    Which of these statements about the electric displacement D→ are correct?
    1. Its flux through any closed surface equals the free charge enclosed.
    2. Its curl is always zero, so it is the gradient of a potential.
    3. In a region of linear dielectrics, its lines begin and end only on free charges.
    4. Its full vector is continuous across any boundary between dielectrics.
    Answer and solution

    Answer: A, C

    ∮D→⋅da→=Qf,enc, so D→ lines start and end only on free charge. But ∇×D→=∇×P→, which need not vanish (for example at the edges of a polarised bar), so D→ is not generally a gradient. At a boundary only D⟂ is continuous (with no free surface charge); D∥ jumps.

    Why people get this wrong: Treating D→ as "just like E→ but with free charge". Its curl is not zero in general, so you cannot use Coulomb's law with free charges to get D→.

  30. MCQExam level

    The gap d of a parallel-plate capacitor (area A) is filled with two layers of equal thickness d/2, one with κ=2 and one with κ=4. The capacitance, in units of ϵ0A/d, is
    1. 8/3
    2. 3
    3. 6
    4. 4/3
    Answer and solution

    Answer: A

    Stacked layers are in series. Each layer: Ci=κiϵ0A/(d/2)=2κiϵ0A/d, giving 4 and 8 (in units of ϵ0A/d). In series: 4×84+8=83.

    Why people get this wrong: 3 is the average of the two constants, which would be the side-by-side (parallel) answer.

← All topics · Timed mock test →