Home / Courses / IIT JAM Physics / Practice / p-n junctions, diodes and Zener diodes

p-n junctions, diodes and Zener diodes

Solid state physics and devices · 79 questions and templates for IIT JAM Physics, in order from warm-up to top rank. Check each answer, then read the full solution.

New to this topic? Read the lesson first: p-n junctions, diodes and Zener diodes.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. MCQWarm-up

    When a p-n junction is forward biased, its depletion region
    1. becomes wider
    2. becomes narrower
    3. stays the same width
    4. moves entirely into the p side
    Answer and solution

    Answer: B

    Forward bias (p side positive) opposes the built-in potential, so the barrier falls from V0 to V0−V. Less uncovered charge is needed to hold a smaller potential step, and the width W∝V0−V shrinks. Reverse bias does the opposite.

    Why people get this wrong: Thinking the applied voltage adds to the barrier in forward bias. Forward bias lowers it.

  2. NATWarm-up

    An ideal diode (ideality factor 1) carries a forward current of 2 mA at room temperature, where VT=kT/e=25 mV. Its dynamic (small-signal) resistance is ______ Ω (to one decimal place).
    Answer and solution

    Answer: 12.5 Ω (±0.1)

    Differentiate I=Is(eV/VT−1): dIdV≈IVT in forward bias. So rd=VTI=25 mV2 mA=12.5 Ω.

    Why people get this wrong: Using V/I at the operating point (the static resistance), which is much larger.

  3. MCQWarm-up

    A Zener diode used to hold a voltage steady is operated
    1. in forward bias above its cut-in voltage
    2. with zero bias
    3. in reverse bias below breakdown
    4. in reverse bias, in its breakdown region
    Answer and solution

    Answer: D

    In reverse breakdown the voltage across a Zener diode stays almost fixed at VZ while the current changes over a wide range. A series resistor takes up the difference between the supply and VZ.

    Why people get this wrong: Thinking breakdown destroys the diode. Zener diodes are designed to work there, as long as the power rating is not exceeded.

  4. MCQWarm-up

    An ideal half-wave rectifier is fed a sine wave of peak Vm. The average (dc) voltage across the load is
    1. Vm/π
    2. 2Vm/π
    3. Vm/2
    4. Vm/2
    Answer and solution

    Answer: A

    Over one period the output is the positive half-sine and then zero: Vdc=12π∫0πVmsin⁡θdθ=2Vm2π=Vmπ=0.318Vm.

    Why people get this wrong: 2Vm/π is the full-wave value; Vm/2 is the rms of the full sine.

  5. MSQWarm-up

    For an unbiased p-n junction in thermal equilibrium, which statements are correct?
    1. The Fermi level is the same throughout.
    2. The diffusion current of each carrier is balanced by its drift current.
    3. The net current is zero.
    4. There is no electric field in the depletion region.
    Answer and solution

    Answer: A, B, C

    Flat Fermi level: true: in equilibrium no net energy flows. Diffusion balanced by drift: true, for electrons and holes separately. Zero current: true. No field: false. The uncovered donor and acceptor ions create a strong field (often 106 to 107 V/m) pointing from n to p; it is what drives the drift current.

    Why people get this wrong: Zero current does not mean no field: two equal and opposite currents flow.

  6. NATWarm-up

    An LED made of a semiconductor with band gap 1.9 eV emits light of wavelength about ______ nm (to the nearest nm). Take hc=1240 eV nm.
    Answer and solution

    Answer: 653 nm (±2)

    Electrons dropping across the gap emit photons of energy close to Eg: λ=hc/Eg=1240/1.9=653 nm, red light.

    Why people get this wrong: Inverting the relation: a larger gap gives a shorter wavelength (towards blue).

  7. MCQWarm-up

    At a typical operating current of about 10 mA, which of these has the largest forward voltage?
    1. a silicon rectifier diode
    2. a germanium diode
    3. a red LED
    4. a blue LED
    Answer and solution

    Answer: D

    The forward voltage is roughly the band gap in electron-volts divided by e, plus a little: germanium about 0.3 V, silicon about 0.7 V, a red LED (Eg≈1.9 eV) about 1.8-2 V and a blue LED (Eg≈2.7 eV, InGaN) about 3 V. Bluer light means bigger photons, so a bigger gap and a bigger voltage.

    Why people get this wrong: Thinking all diodes drop about 0.7 V: that figure is specific to silicon.

  8. NATStandard

    A silicon junction has Na=1017 cm−3 and Nd=1015 cm−3, with ni=1010 cm−3 and kT/e=0.02585 V. Its built-in potential is ______ V (to three decimal places).
    Answer and solution

    Answer: 0.714 V (±0.003)

    V0=kTeln⁡NaNdni2=0.02585ln⁡10321020=0.02585×ln⁡1012=0.02585×27.63=0.714 V.

    Why people get this wrong: Using ln⁡(NaNd/ni) without squaring ni, or log10⁡.

  9. MCQStandard

    In a p+-n junction (Na≫Nd), the depletion region lies
    1. equally on both sides
    2. mostly on the p side
    3. mostly on the n side
    4. outside the junction
    Answer and solution

    Answer: C

    The uncovered charge must balance: Naxp=Ndxn. If Na≫Nd, then xn≫xp: the depletion region spreads into the lightly doped side, which needs a wider region to uncover the same charge.

    Why people get this wrong: Expecting the region to be wider on the heavily doped side. Heavy doping packs the charge into a thin layer.

  10. NATStandard

    A 15 V supply feeds a 9 V Zener diode through a 200 Ω series resistor; a 1 kΩ load is connected across the Zener. The Zener current is ______ mA.
    Answer and solution

    Answer: 21 mA (±0.1)

    The Zener holds the load at 9 V. Series current IS=(15−9)/200=30 mA. Load current IL=9/1000=9 mA. The Zener takes the rest: IZ=30−9=21 mA.

    Why people get this wrong: Forgetting that the load draws part of the series current.

  11. MCQStandard

    The maximum possible efficiency (dc output power over ac input power) of an ideal full-wave rectifier with a resistive load is
    1. 40.6%
    2. 100%
    3. 81.2%
    4. 63.7%
    Answer and solution

    Answer: C

    Full wave: Idc=2Im/π and Irms=Im/2. Efficiency =Idc2RIrms2R=4/π21/2=8π2=81.2%. Half wave gives exactly half, 40.6%. The rest is ripple power, not loss.

    Why people get this wrong: 63.7% is 2/π, the ratio Vdc/Vm, not a power ratio.

  12. NATStandard

    A diode with reverse saturation current 10−12 A and ideality factor 1 is forward biased at 0.60 V, with VT=25.85 mV. The current is ______ mA (to one decimal place).
    Answer and solution

    Answer: 12 mA (±0.15)

    I=Is(eV/VT−1). V/VT=0.60/0.02585=23.21, e23.21=1.20×1010. So I=10−12×1.20×1010=0.0120 A =12.0 mA.

    Why people get this wrong: Tiny changes in V matter: at 0.62 V the current would already be 26 mA.

  13. MCQStandard

    In a centre-tapped full-wave rectifier, each half of the secondary has peak voltage Vm. The peak inverse voltage across each (ideal) diode is
    1. 2Vm
    2. Vm/2
    3. Vm
    4. 2Vm
    Answer and solution

    Answer: A

    When one diode conducts, the output sits at +Vm (its half of the winding) while the other diode's anode is at −Vm (the other half). The reverse voltage across the non-conducting diode is Vm−(−Vm)=2Vm. A bridge rectifier needs diodes rated only for Vm.

    Why people get this wrong: Taking Vm, the bridge value. The centre-tap circuit stresses its diodes twice as much.

  14. MCQStandard

    The ripple factor (rms of the ac part over the dc value) of an unfiltered half-wave rectifier output is
    1. 1.21
    2. 0.48
    3. 0.0
    4. 1.57
    Answer and solution

    Answer: A

    For half wave, Vrms=Vm/2 and Vdc=Vm/π. Ripple factor =(Vrms/Vdc)2−1=(π/2)2−1=2.467−1=1.21. Full wave gives 0.48. The ac part is larger than the dc part, which is why filters are needed.

    Why people get this wrong: 1.57=π/2 is the form factor Vrms/Vdc, not the ripple factor.

  15. MSQStandard

    Which statements about breakdown in p-n junctions are correct?
    1. Zener breakdown happens in heavily doped junctions.
    2. The Zener mechanism is quantum-mechanical tunnelling of electrons across a very thin barrier.
    3. The avalanche breakdown voltage decreases as temperature rises.
    4. Diodes that break down near 5 to 6 V have a temperature coefficient close to zero.
    Answer and solution

    Answer: A, B, D

    Heavily doped: true: the depletion layer is thin and the field enormous. Tunnelling: true. Avalanche falls with T: false. Hotter lattices vibrate more, carriers lose energy in more collisions and need a higher field to start an avalanche, so the avalanche voltage rises (positive coefficient). Zener breakdown has a negative coefficient (the gap shrinks with T). Near 5 to 6 V: true: both mechanisms share the work and the two effects nearly cancel.

    Why people get this wrong: Remembering only that "Zener diodes" break down; most Zener diodes above about 6 V actually work by avalanche.

  16. MCQStandard

    A 5 V source drives a silicon diode through a 1 kΩ resistor. Using the constant-voltage model (0.7 V drop when conducting), the diode current is
    1. 5.0 mA
    2. 5.7 mA
    3. 4.3 mA
    4. 0.7 mA
    Answer and solution

    Answer: C

    Kirchhoff: 5=I(1000)+0.7, so I=4.3/1000=4.3 mA. On the I-V graph this is where the load line from (0,5 mA) to (5 V,0) meets the diode curve.

    Why people get this wrong: Adding the diode drop instead of subtracting it (5.7 mA), or ignoring it (5.0 mA).

  17. MCQStandard

    For an abrupt junction with built-in potential V0 under reverse bias VR, the depletion (junction) capacitance varies as
    1. (V0+VR)−1
    2. (V0+VR)−1/2
    3. (V0+VR)1/2
    4. (V0+VR)−1/3
    Answer and solution

    Answer: B

    The depletion layer acts like a parallel-plate capacitor of gap W: C=εA/W, with W∝(V0+VR)1/2 for an abrupt junction. So C∝(V0+VR)−1/2. A linearly graded junction gives the −1/3 power. Varactor diodes use this voltage-controlled capacitance to tune circuits.

    Why people get this wrong: The −1/3 law belongs to a graded junction, not an abrupt one.

  18. NATStandard

    An LED that drops 2.0 V at its rated current of 15 mA is run from a 5.0 V supply through a series resistor. The resistor needed is ______ Ω (to the nearest whole number).
    Answer and solution

    Answer: 200 $\Omega$ (±1)

    The resistor takes the rest of the supply voltage: 5.0−2.0=3.0 V at 15 mA, so R=3.0/0.015=200 Ω. It dissipates 3.0×0.015=45 mW, so a 14 W part is fine.

    Why people get this wrong: Using the whole 5.0 V (333 Ω): the LED's own drop must be subtracted first.

  19. MCQStandard

    A Schottky (metal-semiconductor) diode is preferred over a p-n diode in fast switching circuits mainly because
    1. it has a higher reverse breakdown voltage
    2. current is carried by majority carriers, so almost no minority charge is stored and it switches off almost at once
    3. its reverse leakage current is smaller
    4. it emits light when forward biased
    Answer and solution

    Answer: B

    In a forward-biased p-n diode, minority carriers are injected and stored on each side; switching off means removing that charge, which takes time (reverse recovery). A Schottky diode conducts by majority carriers crossing the metal-semiconductor barrier, so there is almost no stored charge. It also has a lower forward drop (about 0.2-0.4 V). Its drawbacks are a larger reverse leakage and usually a lower breakdown voltage.

    Why people get this wrong: Choosing "lower leakage": Schottky diodes leak more than p-n diodes.

  20. NATExam level

    A silicon junction (εr=11.7) has Na=1017 cm−3, Nd=1015 cm−3 and built-in potential 0.714 V. At zero bias its depletion width is ______ μm (to two decimal places).
    Answer and solution

    Answer: 0.97 μm (±0.01)

    W=2εV0e(1Na+1Nd) in SI units: Na=1023, Nd=1021 m−3. 2×11.7×8.854×10−12×0.7141.602×10−19=9.23×108; times 1.01×10−21 gives 9.33×10−13 m2; root: W=0.97 μm, almost all on the lightly doped n side.

    Why people get this wrong: Leaving densities in cm−3 inside an SI formula changes the result by a factor of 1000.

  21. NATExam level

    For an ideal diode (ideality factor 1) at room temperature (VT=25.85 mV) in forward bias, the extra voltage needed to raise the current tenfold is ______ mV (to one decimal place).
    Answer and solution

    Answer: 59.5 mV (±0.3)

    Well above Is, I≈IseV/VT, so V2−V1=VTln⁡(I2/I1)=25.85×ln⁡10=25.85×2.303=59.5 mV. Roughly 60 mV per decade of current; a diode with ideality factor η needs η times as much.

    Why people get this wrong: Thinking ten times the current needs ten times the voltage. Diode current is exponential in voltage.

  22. MCQExam level

    At a fixed forward current, the voltage across a silicon diode changes with temperature by about
    1. +2 mV per kelvin
    2. −2 mV per kelvin
    3. −20 mV per kelvin
    4. it does not change
    Answer and solution

    Answer: B

    Is∝ni2 grows very fast with temperature, so less forward voltage is needed for the same current. The net change is about −2 mV/K for silicon. This is used in simple temperature sensors and is why transistor circuits drift when warm.

    Why people get this wrong: The thermal voltage kT/e grows with T, which suggests a positive change, but the rise of Is wins.

  23. NATExam level

    A full-wave rectifier with peak output 20 V feeds a 1 kΩ load in parallel with a 1000 μF capacitor. The supply is 50 Hz. The approximate peak-to-peak ripple voltage is ______ V (to two decimal places).
    Answer and solution

    Answer: 0.2 V (±0.005)

    The capacitor is topped up twice per cycle (every 1/2f=10 ms) and in between discharges through the load at almost constant current I≈Vm/R=20 mA. Ripple ΔV≈I2fC=Vm2fRC=202×50×1000×10−3=0.20 V.

    Why people get this wrong: Using f instead of 2f (half-wave formula) doubles the ripple.

  24. MSQExam level

    Which statements about the reverse saturation current Is of a p-n junction diode are correct?
    1. It depends strongly on temperature.
    2. It is larger for a germanium diode than for a similar silicon diode.
    3. It is proportional to ni2.
    4. Below breakdown, it grows steeply with the reverse voltage.
    Answer and solution

    Answer: A, B, C

    Temperature: true: roughly doubling every 10 K in Si. Ge larger: true: Ge has a smaller gap and ni about 103 times larger. ∝ni2: true: Is=eAni2(DpLpNd+DnLnNa), from minority carriers ni2/N diffusing to the junction. Grows with VR: false: it saturates, because it is limited by how many minority carriers reach the junction, not by the voltage.

    Why people get this wrong: The word "saturation" is the clue: past a few kT/e of reverse bias, the ideal reverse current stops growing.

  25. NATExam level

    A 12 V supply feeds a 6.0 V Zener through a 100 Ω resistor. The Zener needs at least 5 mA to stay in breakdown. The smallest load resistance that still keeps the output regulated is ______ Ω (to the nearest ohm).
    Answer and solution

    Answer: 109 Ω (±1)

    Series current IS=(12−6)/100=60 mA, whatever the load. The load can take at most 60−5=55 mA. So RL,min⁡=6.0/0.055=109 Ω. A smaller load would starve the Zener and the output would fall below 6 V.

    Why people get this wrong: Ignoring the minimum Zener current gives 100 Ω.

  26. MCQExam level

    The signal 5sin⁡ωt V goes through a series capacitor to the output; an ideal diode connects the output to ground with its cathode at the output and anode at ground. After the first few cycles, the output swings between
    1. −5 V and +5 V
    2. 0 and +5 V
    3. −10 V and 0
    4. 0 and +10 V
    Answer and solution

    Answer: D

    Whenever the output tries to go below 0 the diode conducts and charges the capacitor, until the capacitor holds 5 V that lifts the whole wave. Then the most negative point of the output is 0 and the wave swings from 0 to +10 V. This is a positive clamper (dc restorer): the shape is unchanged, only shifted.

    Why people get this wrong: Confusing a clamper with a clipper: a clipper would cut the wave to 0 to +5 V.

  27. NATExam level

    A solar cell gives a photocurrent of 30 mA, has reverse saturation current 10−10 A and ideality factor 1, at VT=25.85 mV. Its open-circuit voltage is ______ V (to three decimal places).
    Answer and solution

    Answer: 0.505 V (±0.003)

    With the photocurrent, I=Is(eV/VT−1)−IL. Open circuit means I=0: Voc=VTln⁡(1+IL/Is)=0.02585ln⁡(3×108+1)=0.02585×19.52=0.505 V.

    Why people get this wrong: Expecting Voc to grow in proportion to the light. It grows only logarithmically.

  28. MCQExam level

    For an abrupt p-n junction, the ratio of the depletion widths on the two sides, xn/xp, equals
    1. Na/Nd
    2. Nd/Na
    3. Na/Nd
    4. 1
    Answer and solution

    Answer: A

    The total charge on the two sides must cancel: eNdxnA=eNaxpA. So xn/xp=Na/Nd. The region is wider on the less doped side.

    Why people get this wrong: Nd/Na inverts it. Think of balancing charges: low density needs more width.

  29. MCQExam level

    Taking current into the p side as positive, a solar cell delivering power to a load works in which quadrant of its I-V graph?
    1. first (V>0, I>0)
    2. second (V<0, I>0)
    3. third (V<0, I<0)
    4. fourth (V>0, I<0)
    Answer and solution

    Answer: D

    A device delivers power when VI<0 with this convention. The illuminated cell has a forward voltage across it (V>0) while the photocurrent flows out of the p side (I<0): the fourth quadrant. A photodiode used as a detector sits in the third quadrant (reverse bias), and a forward-biased LED in the first.

    Why people get this wrong: Picturing the solar cell as a forward-biased diode with forward current: the current is reversed.

  30. NATExam level

    A diode with ideality factor 2 carries 5 mA, with VT=25.85 mV. Its dynamic resistance is ______ Ω (to two decimal places).
    Answer and solution

    Answer: 10.34 Ω (±0.05)

    I=Is(eV/ηVT−1) gives rd=ηVTI=2×0.025850.005=10.34 Ω.

    Why people get this wrong: Leaving out η halves the answer.

← All topics · Timed mock test →