Home / Courses / IIT JAM Physics / Practice / Elasticity: stress, strain and the elastic constants

Elasticity: stress, strain and the elastic constants

Mechanics and properties of matter · 83 questions and templates for IIT JAM Physics, in order from warm-up to top rank. Check each answer, then read the full solution.

New to this topic? Read the lesson first: Elasticity: stress, strain and the elastic constants.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. MCQWarm-up

    Young's modulus of a material is defined as
    1. tensile strain divided by tensile stress
    2. tensile stress divided by tensile strain
    3. force divided by extension
    4. pressure divided by fractional change in volume
    Answer and solution

    Answer: B

    Y=F/AΔL/L: stress over strain, within the range where they are proportional. Force over extension is the spring constant of one particular wire (k=YA/L), not a property of the material. Pressure over volume strain is the bulk modulus.

    Why people get this wrong: Force/extension depends on the wire's length and thickness; the modulus does not.

  2. NATWarm-up

    A steel wire 2 m long with cross-section 1 mm² carries a load of 100 N. With Y=2×1011 Pa, it stretches by ______ mm.
    Answer and solution

    Answer: 1 mm (±0.01)

    ΔL=FLAY=100×210−6×2×1011=10−3 m =1 mm.

    Why people get this wrong: 1 mm² is 10−6 m², not 10−3 m².

  3. MCQWarm-up

    The SI unit of Poisson's ratio is
    1. none: it is a pure number
    2. N/m²
    3. m
    4. N
    Answer and solution

    Answer: A

    Poisson's ratio is (lateral strain)/(longitudinal strain), a ratio of two strains, each a length over a length. It has no unit.
  4. MCQWarm-up

    Which elastic modulus does a liquid have?
    1. Young's modulus only
    2. Shear modulus only
    3. Bulk modulus only
    4. All three
    Answer and solution

    Answer: C

    A liquid resists being squeezed (it has a bulk modulus) but cannot keep a shape: a steady shear simply makes it flow, so its shear modulus is zero, and it has no Young's modulus either.
  5. NATWarm-up

    A rod of cross-section 4 cm² carries a tension of 2000 N. The tensile stress in it is ______ MPa.
    Answer and solution

    Answer: 5 MPa

    Stress =F/A=2000/(4×10−4)=5×106 Pa =5 MPa.
  6. MCQWarm-up

    In the physicist's sense, which is "more elastic": a steel wire or a rubber cord?
    1. Steel, because it needs a much larger stress for the same strain
    2. Rubber, because it stretches more
    3. They are equally elastic
    4. Neither, since both obey Hooke's law exactly
    Answer and solution

    Answer: A

    Elasticity is measured by the modulus: the stress needed per unit strain. Steel (Y≈2×1011 Pa) is about a hundred thousand times stiffer than rubber, so it is far more elastic.

    Why people get this wrong: Everyday language calls rubber "elastic" because it stretches a lot; physics means the opposite.

  7. MCQWarm-up

    A wire of length L, cross-section A and Young's modulus Y is stretched within its elastic limit. Treated as a spring, its force constant (force per unit extension) is
    1. YL/A
    2. Y/(AL)
    3. YA/L
    4. YAL
    Answer and solution

    Answer: C

    Y=F/AΔL/L, so F=YALΔL. The force per unit extension is k=YA/L: a thicker wire is stiffer, a longer one is softer (like springs in series).

    Why people get this wrong: Check with units: YA/L is Pa × m² / m = N/m.

  8. NATStandard

    A wire stretched by 1.5 mm under a steady load of 200 N (within the elastic range) stores ______ J of elastic energy.
    Answer and solution

    Answer: 0.15 J (±0.001)

    The tension rises linearly from 0 to F as it stretches, so U=12FΔL=12×200×1.5×10−3=0.15 J.

    Why people get this wrong: FΔL=0.3 J counts the full force for the whole stretch.

  9. MCQStandard

    Wires A and B are made of the same metal. B is twice as long as A and has twice its diameter. Under the same load, the ratio of extensions ΔLB/ΔLA is
    1. 1/2
    2. 2
    3. 1/4
    4. 1
    Answer and solution

    Answer: A

    ΔL=FL/(AY)∝L/d2. For B: 2/22=1/2 of A's.

    Why people get this wrong: Doubling the diameter quadruples the area.

  10. NATStandard

    The bulk modulus of water is 2.2×109 Pa. At a depth where the extra pressure is 1.1×107 Pa, a sample of water is compressed by ______ % of its volume.
    Answer and solution

    Answer: 0.5 % (±0.005)

    ΔVV=ΔpK=1.1×1072.2×109=0.005=0.5%. Water is nearly, but not perfectly, incompressible.
  11. MCQStandard

    For an isotropic material with Young's modulus Y, shear modulus G and Poisson's ratio σ, which relation is correct?
    1. Y=G(1+σ)
    2. Y=3G(1−2σ)
    3. G=2Y(1+σ)
    4. Y=2G(1+σ)
    Answer and solution

    Answer: D

    The standard results are Y=2G(1+σ) and Y=3K(1−2σ). Quick check: for real solids σ≈0.3, so G≈0.38Y, a bit under half.

    Why people get this wrong: 3(1−2σ) goes with the bulk modulus K, not with G.

  12. NATStandard

    A metal has Y=2.0×1011 Pa and Poisson's ratio 0.25. Its shear modulus is ______ GPa.
    Answer and solution

    Answer: 80 GPa (±0.1)

    G=Y2(1+σ)=2.0×10112.5=8.0×1010 Pa =80 GPa.
  13. MSQStandard

    Which statements about the stress-strain curve of a metal wire are correct?
    1. Stress is proportional to strain up to the proportional limit.
    2. Loaded beyond the elastic limit, the wire keeps a permanent stretch when unloaded.
    3. The ultimate tensile strength is always the stress at which the wire finally breaks.
    4. A brittle material breaks soon after its elastic limit, with little plastic flow.
    Answer and solution

    Answer: A, B, D

    First: Hooke's law region (true). Second: past the elastic limit the deformation is partly plastic (true). Third is false: the ultimate tensile strength is the highest point of the curve; a ductile wire then necks and breaks at a lower (engineering) stress. Fourth: true, which is what "brittle" means (glass, cast iron).
  14. MCQStandard

    For an isotropic elastic material, the theoretical range of Poisson's ratio allowed by the requirement that K and G be positive is
    1. 0 to 1
    2. −1 to 1/2
    3. 1/2 to 1
    4. −1/2 to 1/2
    Answer and solution

    Answer: B

    From Y=3K(1−2σ) with K>0: σ<1/2. From Y=2G(1+σ) with G>0: σ>−1. Most real materials lie between 0.2 and 0.5; some engineered foams have negative values.
  15. NATStandard

    A steel rail is clamped rigidly at both ends with no stress at first. It is then warmed by 50 K. With Y=2×1011 Pa and α=1.2×10−5 K⁻¹, the compressive stress in it is ______ MPa.
    Answer and solution

    Answer: 120 MPa (±0.5)

    It would expand by a strain αΔT; the clamps squeeze it back by the same strain. Stress =YαΔT=2×1011×1.2×10−5×50=1.2×108 Pa =120 MPa. The length does not matter.

    Why people get this wrong: The rail's length cancels; the stress depends only on the strain it is denied.

  16. MCQStandard

    The elastic energy stored per unit volume of a stretched wire (in the Hooke's law region) with strain ε is
    1. Yε2
    2. Yε
    3. 12Yε2
    4. 12Y2ε
    Answer and solution

    Answer: C

    U=12FΔL. Divide by the volume AL: u=12⋅FA⋅ΔLL=12stress×strain=12Yε2.
  17. NATStandard

    A metal has bulk modulus 1.6×1011 Pa. Its compressibility is ______ ×10−12 Pa⁻¹ (two decimal places).
    Answer and solution

    Answer: 6.25 ×10⁻¹² Pa⁻¹ (±0.01)

    Compressibility is the reciprocal of the bulk modulus: 1/(1.6×1011)=6.25×10−12 Pa⁻¹.
  18. MSQStandard

    Which of these quantities have no units (are pure numbers)?
    1. Longitudinal strain
    2. Poisson's ratio
    3. Stress
    4. Shear strain (the angle of shear, in radians)
    Answer and solution

    Answer: A, B, D

    Strains are length over length (or an angle, which is arc over radius), so they have no units, and so has a ratio of strains. Stress is force per area, in pascals.
  19. MCQStandard

    A uniform heavy wire hangs from the ceiling and carries a block at its lower end. The tensile stress in the wire is largest
    1. at the top
    2. at the bottom
    3. at the middle
    4. nowhere: it is the same all along
    Answer and solution

    Answer: A

    The tension at a height in the wire must hold up the block plus all the wire below that point. The top holds the whole wire and the block, so the tension, and with a uniform cross-section the stress, is largest there. It falls linearly to the block's weight alone at the bottom.

    Why people get this wrong: "The same everywhere" is true only for a massless wire.

  20. MCQStandard

    A steel wire (Y=200 GPa) and a copper wire (Y=120 GPa) have the same length and diameter and carry the same load, within their elastic limits. Comparing the elastic energy stored,
    1. steel stores more, because it is more elastic
    2. both store the same, because the load is the same
    3. steel stores 5/3 times as much
    4. copper stores 5/3 times as much
    Answer and solution

    Answer: D

    U=12FΔL with ΔL=FL/(AY), so U=F2L2AY. For the same F, L and A, U∝1/Y: copper stores 200/120=5/3 times as much, because it stretches further under the same force.

    Why people get this wrong: For a fixed load the stiffer wire stretches less and stores less; for a fixed extension it would be the other way round.

  21. MSQStandard

    A uniform rod is clamped without stress between two rigid walls and then warmed by ΔT. Which statements are correct?
    1. The stress in the rod does not depend on the rod's length
    2. The force the rod exerts on each wall is proportional to its cross-sectional area
    3. Doubling the temperature rise doubles the stress
    4. A material with a larger Young's modulus but the same expansion coefficient develops a smaller stress
    Answer and solution

    Answer: A, B, C

    The rod would expand by LαΔT; the walls squeeze it back, so the strain is αΔT and the stress is YαΔT. The length cancels; the stress is linear in ΔT; the force is stress × area, so it scales with A; and a stiffer material (larger Y) gives a larger stress, not a smaller one.

    Why people get this wrong: A longer rod would expand more, but it also has more length to absorb the squeeze: the strain is the same.

  22. NATExam level

    A steel cable 100 m long hangs vertically from its top end, carrying nothing but itself. With density 7800 kg/m³, Y=2×1011 Pa and g=9.8 m/s², it stretches by ______ mm under its own weight (two decimal places).
    Answer and solution

    Answer: 1.91 mm (±0.01)

    At height x above the bottom, the tension supports the cable below: T=ρAgx. A slice dx stretches by TdxAY=ρgxdxY. Integrating from 0 to L: ΔL=ρgL22Y=7800×9.8×1044×1011=1.91×10−3 m.

    Why people get this wrong: The area cancels: a thick cable stretches just as much under its own weight as a thin one.

  23. MCQExam level

    A uniform wire hanging vertically stretches under its own weight W. The same stretch would be produced in a weightless wire of the same size by hanging from its lower end a load of
    1. W
    2. W/2
    3. W/4
    4. 2W
    Answer and solution

    Answer: B

    Own weight: ΔL=ρgL2/2Y=WL2AY, using W=ρgAL. A load F at the end gives FL/AY. Equal when F=W/2: on average, the wire carries half its weight.
  24. MSQExam level

    For an isotropic solid with moduli Y, K, G and Poisson's ratio σ, which relations are correct?
    1. Y=3K(1−2σ)
    2. Y=2G(1+σ)
    3. 9Y=1K+3G
    4. If σ=1/2, the bulk modulus is zero.
    Answer and solution

    Answer: A, B, C

    The first two are the standard results. Eliminating σ between them: σ=1/2−Y/6K and σ=Y/2G−1, so Y/2G+Y/6K=3/2, i.e. 9/Y=1/K+3/G (true). For σ=1/2, 1−2σ=0 so K=Y/0 is infinite: the material is incompressible (fourth false).
  25. NATExam level

    For a metal, Y=1.2×1011 Pa and G=4.5×1010 Pa. Its Poisson's ratio is ______ (three decimal places).
    Answer and solution

    Answer: 0.333 (±0.003)

    σ=Y2G−1=1.2×10119×1010−1=1.333−1=0.333.
  26. NATExam level

    A steel has Y=2.1×1011 Pa and Poisson's ratio 0.3. Its bulk modulus is ______ GPa.
    Answer and solution

    Answer: 175 GPa (±0.5)

    K=Y3(1−2σ)=2.1×10113×0.4=1.75×1011 Pa =175 GPa.
  27. MCQExam level

    The torque needed to twist a wire through angle φ is τ=πGr42Lφ. A second wire of the same metal and length has twice the radius. Its torsion constant is larger by a factor of
    1. 2
    2. 4
    3. 8
    4. 16
    Answer and solution

    Answer: D

    The torsion constant πGr4/2L goes as r4: 24=16. (Each thin cylindrical shell of radius s contributes in proportion to s3ds, which is why the outside of a shaft matters most.)
  28. NATExam level

    A disc with moment of inertia 2×10−3 kg m² hangs from a wire of torsion constant 8×10−3 N m/rad and twists back and forth. Its period is ______ s (two decimal places).
    Answer and solution

    Answer: 3.14 s (±0.01)

    Restoring torque −cφ gives Iφ¨=−cφ, simple harmonic with T=2πI/c=2π0.25=π≈3.14 s.
  29. MCQExam level

    A solid shaft and a hollow shaft are made of the same metal, with the same length and the same mass. Which is harder to twist?
    1. The hollow one
    2. The solid one
    3. They are equally stiff
    4. It depends on the twisting angle
    Answer and solution

    Answer: A

    The torsion constant is πG2L(r24−r14)=πG2L(r22−r12)(r22+r12). Same mass fixes r22−r12; the hollow shaft has the larger r22+r12, because its material sits farther out. That is why drive shafts and bicycle frames are tubes.
  30. MSQExam level

    Two wires of the same metal and length, with cross-sections A and 2A, are joined end to end and hung vertically with a load F at the bottom (ignore their weights). Which statements are correct?
    1. Both carry the same tension F.
    2. The stress in the thin wire is twice that in the thick one.
    3. The thick wire stretches twice as much as the thin one.
    4. The thin wire stores twice as much elastic energy as the thick one.
    Answer and solution

    Answer: A, B, D

    In series the tension is the same, F (true). Stress F/A vs F/2A (true). Extension FL/AY is halved for the thick wire, not doubled (false). Energy 12FΔL=F2L/(2AY) is twice as large in the thin wire (true).

← All topics · Timed mock test →