Magnetic materials: B, H and M
Electricity and magnetism · 77 questions and templates for IIT JAM Physics, in order from warm-up to top rank. Check each answer, then read the full solution.
New to this topic? Read the lesson first: Magnetic materials: B, H and M.
Loading questions… (they need JavaScript; nothing you type is sent anywhere)
Written questions with solutions
The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.
-
MCQWarm-up
The magnetic susceptibility of a diamagnetic material is- small and negative
- small and positive
- large and positive
- exactly
Answer and solution
Answer: A
In a diamagnet the applied field changes the orbital motion of electrons so that the induced moments oppose the field (a Lenz-law effect inside each atom). The magnetisation is opposite to and tiny: for water or copper.Why people get this wrong: is a perfect diamagnet: a superconductor, not an ordinary material.
-
NATWarm-up
A long solenoid with 1000 turns per metre carries 2.0 A and is filled with a soft iron core of relative permeability 500 (take it as linear). The magnetic field inside is ______ T (to two decimal places).Answer and solution
Answer: 1.26 T (±0.01)
Ampère's law for uses only free current: A/m, whatever the core. Then T.Why people get this wrong: Forgetting and getting 2.5 mT, the field without the core.
-
MCQWarm-up
The SI unit of the auxiliary field is- tesla
- ampere per metre
- weber
- ampere square metre
Answer and solution
Answer: B
, so is a current divided by a length: A/m. The magnetisation (magnetic moment per volume, A m/m) has the same unit.Why people get this wrong: Tesla is the unit of ; A m is the unit of a magnetic moment.
-
MSQWarm-up
Which of these statements about ferromagnetic materials are correct?- They show hysteresis.
- Above the Curie temperature they become paramagnetic.
- Their susceptibility is a constant, independent of .
- They are divided into domains, each magnetised to saturation.
Answer and solution
Answer: A, B, D
Ferromagnets are made of domains in which exchange forces line the atomic moments up. Applying grows favourable domains, a process with friction-like irreversibility (hysteresis). Heat above the Curie temperature destroys the order and leaves a paramagnet. Because depends on the history and saturates, is not a constant.Why people get this wrong: "Constant " describes linear (dia- and para-) materials, not ferromagnets.
-
MCQWarm-up
For an ideal paramagnet at ordinary fields, the susceptibility varies with absolute temperature asAnswer and solution
Answer: D
Curie's law: . The field tries to line up the permanent moments, thermal agitation scrambles them; the net alignment is about , which falls as .Why people get this wrong: Diamagnetic susceptibility is almost independent of ; paramagnetic is not.
-
NATWarm-up
In a material, A/m and A/m, both pointing the same way. The magnetic field is ______ mT (to two decimal places).Answer and solution
Answer: 6.28 mT (±0.06)
T.Why people get this wrong: Using and forgetting the magnetisation.
-
MCQWarm-up
Which of these materials has a relative permeability slightly less than 1?- aluminium
- bismuth
- nickel
- platinum
Answer and solution
Answer: B
means : a diamagnet. Bismuth is one of the most strongly diamagnetic elements (). Aluminium and platinum are paramagnetic ( just above 1) and nickel is ferromagnetic ().Why people get this wrong: Assuming every metal is attracted to a magnet.
-
MCQStandard
A long cylinder is uniformly magnetised along its axis with magnetisation . Its bound currents are- a volume current per unit area along the axis
- surface currents (per unit length) on the flat end faces only
- zero everywhere, since is uniform
- a surface current per unit length circling the curved surface, and no volume current
Answer and solution
Answer: D
for uniform . : on the curved side , , so circling round; on the ends and the cross product is zero. The magnet is equivalent to a solenoid with .Why people get this wrong: Uniform kills the volume current but not the surface current.
-
NATStandard
A long iron rod is uniformly magnetised along its length with A/m, with no free current anywhere. Far from its ends, the field inside it is ______ T (to two decimal places).Answer and solution
Answer: 1.01 T (±0.01)
The rod is like a long solenoid with surface current , so inside T.Why people get this wrong: Thinking because there is no free current. is zero there, not .
-
MCQStandard
For the long, uniformly magnetised rod with no free current, far from its ends, inside is- zero
Answer and solution
Answer: C
. Near the ends of a finite rod, is not zero: it points backwards, against (the demagnetising field).Why people get this wrong: Assuming always points along .
-
MSQStandard
At the boundary between two magnetic materials with no free surface current, which field components are continuous?- The normal component of
- The tangential component of
- The tangential component of
- The normal component of
Answer and solution
Answer: A, B
(a pillbox) makes continuous. with no free surface current (a thin loop) makes continuous. The other two jump by the ratio of permeabilities.Why people get this wrong: This is the mirror of the dielectric rules (, ), with playing and playing .
-
NATStandard
A paramagnetic salt obeying Curie's law has susceptibility at 300 K. At 150 K its susceptibility is ______ (to one decimal place).Answer and solution
Answer: 6 $10^{-4}$ (±0.05)
, so .Why people get this wrong: Halving instead of doubling: colder means better alignment, larger .
-
MCQStandard
A type-I superconductor in the Meissner state expels the magnetic field from its interior. Its effective magnetic susceptibility is- 0
Answer and solution
Answer: C
inside for any requires : a perfect diamagnet, with . (Physically, surface supercurrents cancel the field.)Why people get this wrong: is ordinary diamagnetism, far weaker.
-
NATStandard
A toroid of mean radius 10 cm has 500 turns carrying 0.50 A. The magnitude of along its mean circle is ______ A/m (to the nearest whole number).Answer and solution
Answer: 398 A/m (±4)
: A, so A/m. This holds whatever the core is made of; the core changes , not .Why people get this wrong: Using the diameter instead of the radius, or multiplying by (that would be without a core).
-
MCQStandard
Paramagnetism arises from- the alignment, against thermal agitation, of permanent atomic magnetic moments
- currents induced in electron orbits by the applied field
- exchange forces that line up neighbouring moments
- free electrons moving in circles in the field
Answer and solution
Answer: A
Atoms with unpaired electrons have permanent moments. An applied field gives them an energy , so they lean towards the field; heat randomises them. The induced-orbit effect is diamagnetism (present in all materials, usually swamped), and exchange alignment is ferromagnetism.Why people get this wrong: Free electrons give a small paramagnetism (Pauli) and diamagnetism (Landau), but the classic paramagnet is about permanent atomic moments.
-
MCQStandard
The energy dissipated as heat per unit volume of a ferromagnet in one full cycle of magnetisation equals- the remanence times the coercivity
- the area enclosed by its B-H loop
- half the area under the initial magnetisation curve
- the saturation field squared over
Answer and solution
Answer: B
The work done by the source per unit volume to change the field is . Round a closed loop, this is the loop's area. Soft iron (thin loop) wastes little energy per cycle, which is why it is used in transformer cores.Why people get this wrong: Remanence times coercivity has the right units but is only a rough estimate of the area (exactly a quarter of it for a perfectly rectangular loop).
-
NATStandard
Iron has about atoms per m, each with a moment of about 2.2 Bohr magnetons. If all were aligned, the magnetisation would be ______ A/m (to two decimal places). ( J/T.)Answer and solution
Answer: 1.73 $10^6$ A/m (±0.02)
A/m. Then T, close to the saturation field of real iron.Why people get this wrong: Using one Bohr magneton per atom.
-
NATStandard
A small cube of iron, cm on each side, is magnetised to saturation, A/m. Its magnetic dipole moment is ______ A m².Answer and solution
Answer: 1.7 A m² (±0.01)
Magnetisation is dipole moment per unit volume, so A m².Why people get this wrong: Cubing the side in centimetres: m³, not 1.
-
MCQStandard
The Bohr magneton , the natural unit of atomic magnetic moments, is about- J/T
- J/T
- J/T
- J/T
Answer and solution
Answer: B
J/T (the same as A m²). J/T is the nuclear magneton, smaller by the proton-to-electron mass ratio 1836.Why people get this wrong: Mixing up the Bohr magneton and the nuclear magneton.
-
NATExam level
A sphere is uniformly magnetised with A/m. The magnetic field inside it is ______ mT (to one decimal place).Answer and solution
Answer: 83.8 mT (±0.8)
The bound surface current is that of a spinning charged sphere and gives a uniform field inside: T.Why people get this wrong: Using (the long rod). The sphere's shape gives of that.
-
MCQExam level
Inside a uniformly magnetised sphere (no free current), equals- zero
Answer and solution
Answer: A
. Inside a magnet points backwards: this is the demagnetising field, with demagnetising factor for a sphere (0 for a long rod, 1 for a thin disc magnetised across).Why people get this wrong: Taking parallel to , which fails inside permanent magnets.
-
MSQExam level
In a region filled with a uniform linear magnetic material of susceptibility carrying free current density , which statements are correct?- everywhere, including at the material's surface
Answer and solution
Answer: A, B, C
in any static situation, and always. With and constant, . But , which is not zero where changes suddenly, as at a surface.Why people get this wrong: Uniform material is the key: in non-uniform material has an extra part.
-
NATExam level
An iron core () has a mean path length of 0.50 m with an air gap of 1.0 mm cut in it. A winding of 200 turns carries 1.0 A. Neglecting fringing, the field in the gap is ______ T (to three decimal places).Answer and solution
Answer: 0.201 T (±0.002)
is the same in iron and gap (normal component continuous, no fringing). Ampère for : , so T.Why people get this wrong: Ignoring the 1 mm gap because it is short. Its reluctance is four times that of the whole half-metre of iron.
-
MCQExam level
In an electromagnet made of high-permeability iron with a small air gap, the current needed for a given gap field is set mainly by- the length of the iron path
- the cross-section of the iron
- the conductivity of the iron
- the length of the air gap
Answer and solution
Answer: D
The reluctances add in series: iron and gap . With , a gap of a millimetre outweighs a metre of iron, so . The [magnetic circuit solver](/science/magnetic-circuit/) shows the split for any core.Why people get this wrong: The iron path is long but its reluctance is divided by .
-
NATExam level
The B-H loop of a transformer core material encloses 300 J/m. A core of volume m is driven at 50 Hz. The power lost to hysteresis is ______ W.Answer and solution
Answer: 15 W (±0.1)
Each cycle wastes (loop area) (volume) J. At 50 cycles per second: W.Why people get this wrong: Forgetting to multiply by the frequency, or by the volume.
-
MCQExam level
Field lines in air meet the flat surface of a soft iron block () at to the normal. Inside the iron the lines- run almost parallel to the surface
- run almost along the normal
- continue at
- bend to about from the normal
Answer and solution
Answer: A
and continuous give , so , : almost along the surface. Run backwards, lines leaving iron into air come out almost perpendicular to the iron surface, which is why iron pole faces behave like magnetic "equipotentials".Why people get this wrong: Expecting the lines to straighten towards the normal in the denser medium, as light does.
-
NATExam level
Above its Curie point, a ferromagnet follows the Curie-Weiss law . Its susceptibility is 0.010 at 1100 K and 0.005 at 1150 K. The constant is ______ K.Answer and solution
Answer: 1050 K (±1)
Dividing: , so and K. Then K.Why people get this wrong: Using Curie's law , which would give inconsistent values.
-
MSQExam level
Which statements about diamagnetism are correct?- It is present in all materials.
- Its susceptibility hardly depends on temperature.
- A diamagnetic sample is pulled towards the region of stronger field.
- It comes from the change in electron orbital motion induced by the applied field.
Answer and solution
Answer: A, B, D
Every atom's electron orbits respond to an applied field by Lenz's law, giving a moment against the field, so all matter is diamagnetic (it is just masked in para- and ferromagnets). The effect does not rely on alignment against heat, so it is nearly independent of . With the energy is lowest where is weak, so diamagnets are pushed out of strong fields (levitated frogs).Why people get this wrong: Paramagnets are pulled in; diamagnets are pushed out.
-
NATExam level
A cylindrical bar magnet, uniformly magnetised along its axis with A/m, is 10 cm long. The total bound current circulating round its curved surface is ______ kA.Answer and solution
Answer: 20 kA (±0.1)
A per metre of length. Over 0.10 m: A kA. A magnet is equivalent to a huge current, which is why it is easy to make strong fields with permanent magnets and hard with wires.Why people get this wrong: Multiplying by the circumference: is current per unit length along the axis.
-
MCQExam level
A long cylinder (axis ) has magnetisation in cylindrical coordinates, where is a constant. The bound volume current density is- zero
Answer and solution
Answer: C
. Other components vanish. So . On the surface ; total current , as for any bound current crossing a section.Why people get this wrong: Forgetting the factor and the inside the derivative (the curvilinear curl), which gives .