Home / Courses / IIT JAM Physics / Practice / Operational amplifiers

Operational amplifiers

Electronics · 83 questions and templates for IIT JAM Physics, in order from warm-up to top rank. Check each answer, then read the full solution.

New to this topic? Read the lesson first: Operational amplifiers.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. MCQWarm-up

    Which of the following is NOT a property of an ideal operational amplifier?
    1. Infinite open-loop voltage gain
    2. Infinite input impedance
    3. Infinite output impedance
    4. Infinite bandwidth
    Answer and solution

    Answer: C

    An ideal op-amp has infinite gain, infinite bandwidth and infinite input impedance (no current flows into its inputs). Its output should behave like a perfect voltage source that holds its voltage whatever the load draws, which means ZERO output impedance.

    Why people get this wrong: The ideal is "infinite" for almost everything, which tempts people to say the same of the output impedance.

  2. NATWarm-up

    An ideal inverting amplifier has input resistor 10 kΩ and feedback resistor 100 kΩ. For a DC input of 0.2 V the output is ______ V.
    Answer and solution

    Answer: -2 V (±0.001)

    Gain =−Rf/Rin=−100/10=−10, so Vo=−10×0.2=−2 V.

    Why people get this wrong: The minus sign is part of the answer: the inverting amplifier flips the polarity.

  3. MCQWarm-up

    A non-inverting amplifier uses Rf=90 kΩ from output to the inverting input and R1=10 kΩ from the inverting input to ground. Its voltage gain is
    1. 9
    2. 10
    3. −9
    4. 11
    Answer and solution

    Answer: B

    The divider feeds back R1/(R1+Rf)=1/10 of the output. With the inputs held equal, Vin=Vo/10, so the gain is 1+Rf/R1=1+9=10.

    Why people get this wrong: 9 is Rf/R1, the inverting amplifier's gain magnitude; the non-inverting one adds 1.

  4. MCQWarm-up

    A voltage follower (output tied straight to the inverting input, signal into the non-inverting input) is useful because
    1. it has a gain of −1, so it inverts the signal
    2. it has infinite gain, so it detects tiny signals
    3. it has zero gain, so it blocks the signal
    4. it has a gain of 1 with a very high input impedance and a very low output impedance
    Answer and solution

    Answer: D

    With full feedback, V−=Vo and the virtual short gives Vo=V+=Vin: gain +1. It draws almost no current from the source and can drive heavy loads, so it is a buffer between a weak source and a demanding load.

    Why people get this wrong: A gain of 1 sounds useless, but the job of a buffer is impedance, not gain.

  5. NATWarm-up

    A non-inverting amplifier has Rf=47 kΩ and R1=4.7 kΩ. For an input of 0.3 V the output is ______ V.
    Answer and solution

    Answer: 3.3 V (±0.01)

    Gain =1+Rf/R1=1+10=11; Vo=11×0.3=3.3 V, with the same sign as the input.

    Why people get this wrong: Using Rf/R1=10 gives 3.0 V.

  6. MCQWarm-up

    In an inverting amplifier the inverting input is called a "virtual ground". This means
    1. it is connected to ground through a wire inside the op-amp
    2. current flows from it straight to ground
    3. it stays at (almost) zero volts because negative feedback keeps the two inputs equal, though no current flows to ground through it
    4. it carries the full output voltage
    Answer and solution

    Answer: C

    The non-inverting input is grounded. With a huge gain and negative feedback, the output settles where V+−V−=Vo/A≈0, so V−≈0. But no current enters the op-amp input, so all the input current goes on through Rf: the node is at ground potential without being connected to ground.

    Why people get this wrong: If it really were grounded, the input current would vanish into ground and the output would be zero.

  7. MCQWarm-up

    The two "golden rules" for an ideal op-amp circuit (the inputs draw no current, and the two input voltages are equal) can be used
    1. whenever the op-amp is powered
    2. only when there is negative feedback and the output is not saturated
    3. only when there is positive feedback
    4. only for ac signals
    Answer and solution

    Answer: B

    The rule "no input current" is a property of the device. The rule V+=V− is not: it is what negative feedback achieves, by adjusting the output until the tiny difference times the huge gain gives the needed output. Without feedback (a comparator), with positive feedback (a Schmitt trigger) or once the output hits a supply rail, the inputs can differ by volts.

    Why people get this wrong: Applying V+=V− to a comparator or a saturated amplifier.

  8. NATStandard

    An inverting summing amplifier has Rf=30 kΩ. Input V1=2 V is applied through 20 kΩ and V2=0.3 V through 10 kΩ. The output is ______ V.
    Answer and solution

    Answer: -3.9 V (±0.01)

    The currents add at the virtual ground: Vo=−Rf(V1/R1+V2/R2)=−(1.5×2+3×0.3)=−(3+0.9)=−3.9 V.

    Why people get this wrong: Each input has its own weight Rf/Ri; adding the inputs first and using one gain is wrong here.

  9. MCQStandard

    An inverting amplifier with gain −20 runs from ±12 V supplies; its output can swing only to ±11 V. For a DC input of +0.8 V the output is
    1. −16 V
    2. −11 V
    3. +11 V
    4. −12 V
    Answer and solution

    Answer: B

    The ideal output would be −20×0.8=−16 V, but the output cannot go beyond the negative saturation level, −11 V. The op-amp saturates there and the virtual short no longer holds.

    Why people get this wrong: The formula −Rf/Rin is valid only while the output stays within the rails.

  10. MCQStandard

    A difference amplifier is built with four equal resistors. V1=3 V goes to the resistor on the inverting side and V2=5 V to the resistor on the non-inverting side. The output is
    1. +8 V
    2. −2 V
    3. +2 V
    4. 0 V
    Answer and solution

    Answer: C

    With equal resistors, V+=V2/2. Superposition: Vo=(1+R/R)V+−(R/R)V1=2(V2/2)−V1=V2−V1=5−3=+2 V.

    Why people get this wrong: The sign depends on which input reaches which terminal; the non-inverting input carries the plus sign.

  11. NATStandard

    An op-amp has a slew rate of 0.5 V/μs. The highest frequency at which it can deliver an undistorted sine wave of 10 V peak is ______ kHz (to two decimal places).
    Answer and solution

    Answer: 7.96 kHz (±0.05)

    For Vpsin⁡2πft the steepest slope is 2πfVp (at the zero crossings). It must not exceed the slew rate: fmax=SR/(2πVp)=5×105/(2π×10)=7958 Hz =7.96 kHz.

    Why people get this wrong: Using peak-to-peak (20 V) halves the answer; the slope uses the peak amplitude.

  12. NATStandard

    An op-amp has a gain-bandwidth product of 1 MHz. Used as a non-inverting amplifier with gain 20, its −3 dB bandwidth is ______ kHz.
    Answer and solution

    Answer: 50 kHz (±0.1)

    For a single-pole op-amp, closed-loop gain times bandwidth stays equal to the gain-bandwidth product: f3dB=1 MHz/20=50 kHz.

    Why people get this wrong: For an inverting amplifier the divisor is the noise gain 1+Rf/Rin, not Rf/Rin; here the stage is non-inverting so it is just 20.

  13. MSQStandard

    Negative feedback is applied around an op-amp to make an amplifier. Compared with the open-loop op-amp, which statements are correct?
    1. The voltage gain is reduced.
    2. The bandwidth is increased.
    3. Distortion is reduced.
    4. The gain now depends mainly on the op-amp's open-loop gain.
    Answer and solution

    Answer: A, B, C

    With feedback fraction β, the gain becomes A/(1+Aβ)≈1/β: much smaller, but set by resistors rather than by the large, unreliable A. The same factor 1+Aβ widens the bandwidth and divides the distortion. So the gain becomes nearly INDEPENDENT of the open-loop gain.

    Why people get this wrong: The whole point of feedback is that the gain stops depending on A.

  14. MCQStandard

    An ideal integrator has R=10 kΩ and C=1 μF, and its output starts at 0 V. A constant +1 V is applied to its input. After 20 ms the output is
    1. +2 V
    2. −20 V
    3. −0.2 V
    4. −2 V
    Answer and solution

    Answer: D

    A constant current Vin/R=0.1 mA charges the capacitor, so the output ramps: Vo=−1RC∫0tVindt=−VintRC=−1×0.020.01=−2 V.

    Why people get this wrong: The inverting integrator ramps the opposite way to the input: the sign is negative.

  15. MCQStandard

    An op-amp has differential gain 105 and common-mode gain 1. Its common-mode rejection ratio is
    1. 50 dB
    2. 100 dB
    3. 105 dB
    4. 5 dB
    Answer and solution

    Answer: B

    CMRR=Ad/Acm=105, and in decibels 20log10⁡105=100 dB.

    Why people get this wrong: 10log10⁡ (50 dB) is for power ratios; gains of voltage use 20log10⁡.

  16. MCQStandard

    An inverting amplifier has Rin=4.7 kΩ and Rf=47 kΩ, built with an ideal op-amp. The input resistance seen by the signal source is
    1. infinite
    2. 4.7 kΩ
    3. 47 kΩ
    4. 0 Ω
    Answer and solution

    Answer: B

    The source drives Rin, whose other end sits at the virtual ground. So the current is Vin/Rin and the input resistance is just Rin=4.7 kΩ, however ideal the op-amp is.

    Why people get this wrong: The op-amp's own input is infinite, but in the inverting circuit the source sees Rin. Only the non-inverting circuit gives the very high input resistance.

  17. MSQStandard

    An op-amp is used without feedback as a comparator. Which statements are correct?
    1. Its output sits near one supply rail or the other.
    2. It relies on negative feedback to keep its inputs equal.
    3. A differential input of a few millivolts is enough to saturate the output.
    4. When V+>V− the output is at positive saturation.
    Answer and solution

    Answer: A, C, D

    With no feedback the full open-loop gain (around 105) acts on V+−V−, so even a millivolt or so drives the output to a rail: positive when V+>V−, negative otherwise. There is no feedback, so the virtual short does not apply and the inputs can differ by volts.

    Why people get this wrong: The rule "inputs equal" is a consequence of negative feedback, not a property of the op-amp itself.

  18. MSQStandard

    Which of these circuits (ideal op-amps, mid-band) give an output in phase with the input?
    1. A non-inverting amplifier of gain 5
    2. A voltage follower
    3. An inverting amplifier with Rf=Rin
    4. Two inverting amplifiers connected one after the other
    Answer and solution

    Answer: A, B, D

    Non-inverting amplifiers and the follower have positive gain. An inverting amplifier with equal resistors has gain −1: same size, opposite phase. Two inverting stages give (−)(−)=+: in phase overall.

    Why people get this wrong: Gain −1 keeps the size of the signal but still flips it by 180∘.

  19. NATStandard

    Two inputs, 2.0 V and 4.0 V, are each connected through a 10 kΩ resistor to the non-inverting input of an ideal op-amp (nothing else connects there). The op-amp has Rf=20 kΩ from output to inverting input and R1=10 kΩ from inverting input to ground. The output is ______ V (to one decimal place).
    Answer and solution

    Answer: 9 V (±0.05)

    No current enters the non-inverting input, so the two equal resistors form a divider that averages the inputs: V+=(2.0+4.0)/2=3.0 V. The stage is a non-inverting amplifier of gain 1+Rf/R1=3, so Vout=9.0 V. This non-inverting summer gives Vout=V1+V2 when the gain equals the number of inputs.

    Why people get this wrong: Treating it like the inverting summer (adding currents into a virtual ground) gives −12 V.

  20. MCQStandard

    An ideal inverting amplifier has Rin=10 kΩ and Rf=100 kΩ. The input resistance seen by the signal source is
    1. infinite, because the op-amp draws no current
    2. zero, because of the virtual ground
    3. 10 kΩ
    4. 100 kΩ
    Answer and solution

    Answer: C

    The inverting input is held at (virtual) ground, so the source sees Rin going to ground: the input current is Vin/Rin and the input resistance is 10 kΩ. This is a weakness of the inverting stage: raising its input resistance means raising both resistors. The non-inverting stage, by contrast, has a very high input resistance.

    Why people get this wrong: "Op-amps have infinite input resistance" describes the op-amp's own terminals, not this circuit's input.

  21. NATExam level

    An op-amp with open-loop gain A=1000 is used in a non-inverting amplifier whose resistor divider feeds back β=0.1 of the output. The closed-loop gain is ______ (to three decimal places).
    Answer and solution

    Answer: 9.901 (±0.002)

    From Vo=A(Vin−βVo): Vo/Vin=A/(1+Aβ)=1000/(1+100)=9.901. The ideal value 1/β=10 is off by about 1% because the loop gain Aβ=100 is not infinite.

    Why people get this wrong: Using the ideal value 10 is wrong when the question gives a finite A.

  22. MCQExam level

    A triangular wave is fed into an ideal op-amp differentiator. The output is
    1. a sine wave
    2. a triangular wave of the opposite sign
    3. a square wave
    4. a train of narrow spikes
    Answer and solution

    Answer: C

    The differentiator gives Vo=−RCdVin/dt. A triangle has a constant positive slope on the way up and a constant negative slope on the way down, so the output jumps between two constant levels: a square wave. (A square wave in gives spikes; the integrator undoes these steps.)

    Why people get this wrong: Spikes are what a differentiator makes from a square wave, not from a triangle.

  23. NATExam level

    An inverting amplifier has a 0.01 μF capacitor in parallel with its 10 kΩ feedback resistor, making a first-order low-pass filter. Its cut-off frequency is ______ Hz (to the nearest whole number).
    Answer and solution

    Answer: 1592 Hz (±3)

    The feedback impedance is Rf∥(1/jωC), so the gain falls by 2 where ωRfC=1: fc=1/(2πRfC)=1/(2π×104×10−8)=1592 Hz. The input resistor sets only the pass-band gain.

    Why people get this wrong: Using the input resistor in fc: the capacitor is across Rf, so only Rf counts.

  24. MCQExam level

    A Wien bridge oscillator uses a non-inverting amplifier with resistors Rf (feedback) and R1 (to ground). For oscillations to just start and be sustained, the resistors must satisfy (at least)
    1. Rf=R1
    2. Rf=2R1
    3. Rf=3R1
    4. Rf=29R1
    Answer and solution

    Answer: B

    At its centre frequency f=1/(2πRC) the Wien network has zero phase shift and passes 1/3 of the voltage. Barkhausen: the loop gain must be 1, so the amplifier needs gain 3=1+Rf/R1, i.e. Rf=2R1.

    Why people get this wrong: Rf=3R1 gives gain 4 (it confuses Rf/R1 with the gain); 29 belongs to the RC phase-shift oscillator.

  25. NATExam level

    An inverting Schmitt trigger has its output (±12 V saturation) fed back to the non-inverting input through R2=20 kΩ, and R1=10 kΩ from the non-inverting input to ground. The width of its hysteresis band (upper threshold minus lower threshold) is ______ V.
    Answer and solution

    Answer: 8 V (±0.01)

    The non-inverting input sits at VoR1/(R1+R2)=Vo/3. With Vo=+12 V the threshold is +4 V; with Vo=−12 V it is −4 V. The width is 4−(−4)=8 V.

    Why people get this wrong: Using R1/R2 instead of R1/(R1+R2) gives thresholds of ±6 V.

  26. MSQExam level

    Which statements about the ideal op-amp integrator (input resistor R, feedback capacitor C) are correct?
    1. Vo=−1RC∫Vindt.
    2. The magnitude of its gain rises with frequency.
    3. At DC its gain is unlimited, so even a tiny input offset slowly drives it into saturation.
    4. A large resistor is often placed across C to limit its gain at low frequencies.
    Answer and solution

    Answer: A, C, D

    The input current Vin/R flows on into the capacitor, so CdVo/dt=−Vin/R. In terms of frequency the gain is −1/(jωRC), whose size FALLS as 1/ω (that is the differentiator that rises). At ω→0 the gain is unbounded, so offsets integrate up to a rail; a resistor across C caps the DC gain at −Rf/R.

    Why people get this wrong: Integrator and differentiator are easy to swap: the integrator is a low-pass circuit.

  27. MCQExam level

    An ideal integrator with R=10 kΩ and C=0.1 μF receives Vin=2sin⁡(1000t) V. Ignoring any constant, the output is
    1. 2cos⁡(1000t) V
    2. −2cos⁡(1000t) V
    3. 2000cos⁡(1000t) V
    4. −2sin⁡(1000t) V
    Answer and solution

    Answer: A

    RC=104×10−7=10−3 s. Vo=−1RC∫2sin⁡(1000t)dt=−1000×(−21000cos⁡1000t)=2cos⁡(1000t) V. The amplitude is unchanged because ωRC=1 at this frequency.

    Why people get this wrong: Two minus signs (the inverting circuit and the integral of sine) cancel; dropping either gives −2cos⁡.

  28. NATExam level

    A three-op-amp instrumentation amplifier has input-stage resistors R=25 kΩ on each side, a gain-setting resistor RG=1 kΩ between them, and a unity-gain difference stage. Its differential gain is ______.
    Answer and solution

    Answer: 51 (±0.01)

    The two input followers force the input difference across RG, so the current (V2−V1)/RG flows through R+RG+R. The difference between the two buffer outputs is (V2−V1)(1+2R/RG), and the unity difference stage passes it on: gain 1+2×25/1=51.

    Why people get this wrong: 1+R/RG=26 forgets that there is a resistor R on each side.

  29. MCQExam level

    An op-amp with input offset voltage 2 mV is used in an inverting amplifier with Rf/Rin=100. With the input grounded, the output offset is about
    1. 200 mV
    2. 202 mV
    3. 2 mV
    4. 20 mV
    Answer and solution

    Answer: B

    The offset acts like a small source in series with the non-inverting input. For that source the circuit is a non-inverting amplifier with gain 1+Rf/Rin=101 (the "noise gain"). Output offset =101×2 mV =202 mV.

    Why people get this wrong: The signal gain is 100, but the offset sees the noise gain, 101.

  30. MCQExam level

    To cancel the effect of the input bias currents in an inverting amplifier with Rin=10 kΩ and Rf=100 kΩ, a resistor is placed between the non-inverting input and ground. Its best value is about
    1. 9.1 kΩ
    2. 110 kΩ
    3. 10 kΩ
    4. 100 kΩ
    Answer and solution

    Answer: A

    Each input should see the same DC resistance, so that equal bias currents make equal voltage drops. The inverting input sees Rin and Rf in parallel (the source and output are both at low impedance): 10∥100=9.09 kΩ.

    Why people get this wrong: 110 kΩ puts the resistors in series; from the input node they are in parallel.

← All topics · Timed mock test →