Home / Courses / IIT JAM Physics / Practice / Diodes, BJTs, FETs and MOSFETs

Diodes, BJTs, FETs and MOSFETs

Electronics · 8 questions and templates for IIT JAM Physics, in order from warm-up to top rank. Check each answer, then read the full solution.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. MCQWarm-up

    Why is the DC gate current of a MOSFET practically zero?
    1. The gate is separated from the channel by an insulating oxide layer
    2. The gate-channel junction is reverse biased
    3. The channel has no free carriers until the gate current flows
    4. The source and drain are shorted together
    Answer and solution

    Answer: A

    The gate electrode sits on a thin insulator (SiO2 or a high-κ oxide). It forms a capacitor with the channel: charge on the gate induces the channel charge, but no steady current crosses the insulator. Input resistances of 1012Ω or more are typical.

    Why people get this wrong: A reverse-biased junction is the reason for the JFET, which still has a small leakage current, not the MOSFET.

  2. MCQWarm-up

    An ideal diode (ideality factor 1) carries a forward bias current of 2 mA. Taking VT=26 mV, its small-signal (dynamic) resistance is
    1. 13 Ω
    2. 26 Ω
    3. 52 Ω
    4. 0.077 Ω
    Answer and solution

    Answer: A

    From I=I0eV/VT, dI/dV=I/VT, so rd=VT/I=26 mV/2 mA=13 Ω. It is the inverse of the slope of the I-V curve at the bias point, not V/I.

    Why people get this wrong: I/VT=0.077 S is the conductance, not the resistance; and 26 Ω would need an ideality factor of 2.

  3. MCQStandard

    A silicon diode carries a constant forward current. As its temperature rises, its forward voltage
    1. rises by about 2 mV per kelvin
    2. stays the same
    3. falls by about 25 mV per kelvin
    4. falls by about 2 mV per kelvin
    Answer and solution

    Answer: D

    The saturation current IS∝ni2∝T3e−Eg/kBT grows very fast with temperature, so a smaller voltage is needed for the same current. For silicon the net effect is about −2 mV/K, used in diode thermometers.

    Why people get this wrong: Thinking only of VT=kBT/q in the exponent, which alone would make V rise; the growth of IS wins.

  4. MCQStandard

    A silicon abrupt junction at 300 K has NA=1.0×1017 cm−3 on the p side and ND=1.0×1015 cm−3 on the n side, with ni=1.0×1010 cm−3 and kBT/e=25.85 mV. Its built-in potential is closest to
    1. 0.36 V
    2. 0.60 V
    3. 0.71 V
    4. 0.83 V
    Answer and solution

    Answer: C

    Vbi=kBTeln⁡NANDni2=0.02585ln⁡1017×10151020=0.02585ln⁡1012=0.02585×27.63=0.714 V.

    Why people get this wrong: Using only one doping twice (ND2 gives 0.60 V, NA2 gives 0.83 V) or halving the logarithm (0.36 V).

  5. MCQExam level

    A heavily doped junction breaks down at about 3 V. The mechanism and the sign of the temperature coefficient of its breakdown voltage are
    1. avalanche multiplication, positive
    2. Zener (band-to-band) tunnelling, negative
    3. avalanche multiplication, negative
    4. thermal runaway, positive
    Answer and solution

    Answer: B

    Heavy doping gives a very thin depletion layer and huge fields, so electrons tunnel from the valence band on one side into the conduction band on the other. A higher temperature shrinks the gap and makes tunnelling easier: negative coefficient. Avalanche breakdown (above about 6 V) has a positive coefficient because phonon scattering shortens the free path; diodes near 5-6 V have almost zero drift.

    Why people get this wrong: Every breakdown diode is sold as a "Zener", but true Zener tunnelling is the low-voltage one.

  6. MCQHard

    A silicon diode's reverse saturation current is 10 nA at 25∘C and roughly doubles every 10∘C. At 75∘C it is about
    1. 50 nA
    2. 160 nA
    3. 1.0 μA
    4. 320 nA
    Answer and solution

    Answer: D

    A rise of 50 °C is five doublings: 10×25=320 nA.

    Why people get this wrong: Adding 10 nA per step (50 nA) or stopping at four doublings (160 nA).

← All topics · Timed mock test →