Home / Courses / IIT JAM Physics / Practice / Semiconductors, Landau levels and the Hall effect

Semiconductors, Landau levels and the Hall effect

Solid state physics and devices · 10 questions and templates for IIT JAM Physics, in order from warm-up to top rank. Check each answer, then read the full solution.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. MCQWarm-up

    An n-type semiconductor bar (all donors ionised, intrinsic carriers negligible) shows a Hall voltage VH at a given current and magnetic field. An otherwise identical bar with twice the donor density, at the same current and field, shows
    1. 2VH
    2. VH/2
    3. the same VH
    4. VH/4
    Answer and solution

    Answer: B

    VH=IB/(nqt) for a bar of thickness t. With twice the carriers, each moves half as fast for the same current, so the magnetic force and the Hall field are halved: VH/2. This is why Hall sensors use lightly doped semiconductors rather than metals.

    Why people get this wrong: More carriers do not mean more Hall voltage; the Hall voltage measures the drift speed, which falls.

  2. NATStandard

    An n-type sample has Hall coefficient RH=−2.5×10−3 m3/C and conductivity 100 S/m (single carrier type, Hall factor 1). The electron mobility is ______ m2/V s (to two decimal places).
    Answer and solution

    Answer: 0.25 (±0.005)

    |RH|=1/(ne) and σ=neμ, so μ=|RH|σ=2.5×10−3×100=0.25 m2/V s. The carrier density is 1/(e|RH|)=2.5×1021 m−3.

    Why people get this wrong: Dividing σ by RH instead of multiplying; check the units: (m3/C)(S/m) = m2/V s.

  3. MSQStandard

    For a Hall measurement on a bar with one type of carrier, which statements are correct?
    1. RH=1/(qn) with q the carrier charge, so n-type samples give a negative Hall coefficient.
    2. At fixed current and field, a thinner bar gives a larger Hall voltage.
    3. The Hall voltage is proportional to the product of the current and the magnetic field.
    4. A more heavily doped bar gives a larger Hall voltage.
    Answer and solution

    Answer: A, B, C

    Balancing qEH=qvB with I=nqvwt gives EH=IB/(nqwt) and VH=EHw=IB/(nqt). So VH∝IB/(nt): thinner is larger, more carriers smaller. RH=EH/(JB)=1/(nq) takes the sign of the carrier charge.

    Why people get this wrong: A thin bar has a smaller cross-section, so the carriers move faster for the same current: larger Hall voltage.

  4. MCQExam level

    For an intrinsic semiconductor ni∝T3/2e−Eg/2kBT. A plot of ln⁡(ni/T3/2) against 1/T is a straight line of slope
    1. −Eg/kB
    2. −Eg/2kB
    3. −Eg/4kB
    4. +Eg/2kB
    Answer and solution

    Answer: B

    ln⁡(ni/T3/2)=const−Eg2kB⋅1T. Each carrier needs half the gap measured from the intrinsic Fermi level near mid-gap, hence Eg/2. (Conductivity data give the same slope if mobility changes slowly.)

    Why people get this wrong: Using −Eg/kB doubles the gap you extract; the factor 2 comes from ni=np.

  5. NATExam level

    Silicon with ni=1.0×1016 m−3 at 300 K is doped with 5.0×1021 m−3 donors (all ionised). The hole density is ______ ×1010 m−3 (one decimal place).
    Answer and solution

    Answer: 2 $10^{10}$ m$^{-3}$ (±0.02)

    With Nd≫ni, n≈Nd=5.0×1021 m−3. Mass action: p=ni2/n=(1.0×1016)2/5.0×1021=2.0×1010 m−3, eleven orders of magnitude fewer than the electrons.

    Why people get this wrong: Assuming the holes stay at ni ignores the mass-action law.

  6. NATExam level

    Silicon at 300 K (kBT=25.85 meV, effective density of states Nc=2.8×1025 m−3) is doped with 1.0×1022 m−3 fully ionised donors. The Fermi level lies ______ eV below the conduction band edge (to three decimal places).
    Answer and solution

    Answer: 0.205 (±0.002)

    For a non-degenerate semiconductor n=Nce−(Ec−EF)/kBT, and here n=Nd. So Ec−EF=kBTln⁡(Nc/Nd)=0.02585ln⁡2800=0.02585×7.937=0.205 eV. Ten times more doping moves EF up by kBTln⁡10=60 meV.

    Why people get this wrong: Using log10⁡ gives 0.089 eV.

  7. MCQExam level

    A silicon sample contains 5.0×1022 m−3 donors and 2.0×1022 m−3 acceptors, all ionised, and its electron mobility is 0.12 m2/V s (holes negligible). Its conductivity is about
    1. 1346 S/m
    2. 577 S/m
    3. 961 S/m
    4. 384 S/m
    Answer and solution

    Answer: B

    The acceptors capture electrons from donors, so n=Nd−Na=3.0×1022 m−3. σ=neμ=3.0×1022×1.602×10−19×0.12=577 S/m. (All 7×1022 ionised centres still scatter the electrons, which is already in the quoted mobility.)

    Why people get this wrong: Adding the dopant densities counts acceptors as if they gave electrons.

← All topics · Timed mock test →