Home / Courses / Medical entrance (NEET) / Practice / Experimental skills and practical physics

Experimental skills and practical physics

Class 12 · 254 questions and templates for Medical entrance (NEET), in order from warm-up to top rank. Check each answer, then read the full solution.

New to this topic? Read the lesson first: Experimental skills and practical physics.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. NATWarm-up

    In a vernier calliper, 1 main scale division (MSD) is 1 mm and 50 vernier divisions equal 49 MSD. Find the least count in mm.
    Answer and solution

    Answer: 0.02 mm (±0.0005)

    Least count = 1 MSD ÷ (number of vernier divisions) =1/50=0.02 mm.
  2. NATWarm-up

    A screw gauge has pitch 0.5 mm and 50 divisions on its circular scale. Find the least count in mm.
    Answer and solution

    Answer: 0.01 mm (±0.0005)

    Least count = pitch ÷ number of circular divisions =0.5/50=0.01 mm.
  3. MCQWarm-up

    Which instrument is the best choice to measure the diameter of a thin wire to 0.01 mm?
    1. Metre scale
    2. Screw gauge
    3. Vernier calliper with least count 0.1 mm
    4. Measuring tape
    Answer and solution

    Answer: B

    The screw gauge usually reads to 0.01 mm. The metre scale reads only to 1 mm. A vernier calliper of least count 0.1 mm is too coarse, and a tape is coarser still.
  4. MCQWarm-up

    A vernier calliper has a positive zero error. To get the true reading we should
    1. subtract the zero error from the observed reading
    2. add the zero error to the observed reading
    3. ignore the zero error
    4. multiply the reading by the zero error
    Answer and solution

    Answer: A

    True reading = observed reading − zero error. For a positive zero error the instrument reads too much when closed, so its readings are too large and we subtract. (For a negative zero error the subtraction of a negative number adds.)
  5. MCQWarm-up

    The time period of a simple pendulum (small oscillations) does not depend on
    1. its length
    2. the value of g
    3. the place where it is used
    4. the mass of the bob
    Answer and solution

    Answer: D

    T=2πL/g has no mass in it. It depends on the length and on g, and g changes with place.
  6. MCQWarm-up

    In a simple pendulum experiment the length L is measured from the point of suspension to
    1. the top of the bob
    2. the bottom of the bob
    3. the centre of the bob
    4. the middle of the thread
    Answer and solution

    Answer: C

    The formula T=2πL/g uses the distance to the centre of mass of the bob: string length plus the radius of the bob.
  7. MCQWarm-up

    In a metre bridge the balance point is found at 50 cm from the left end. The known resistance in the left gap is 12 Ω. The unknown resistance in the right gap is
    1. 6 Ω
    2. 12 Ω
    3. 24 Ω
    4. 50 Ω
    Answer and solution

    Answer: B

    At the null point R/S=l/(100−l)=50/50=1, so the two resistances are equal.
  8. MCQWarm-up

    In an experiment to verify Ohm's law, the ammeter and voltmeter are connected as
    1. ammeter in series, voltmeter in parallel with the resistor
    2. ammeter in parallel, voltmeter in series
    3. both in series
    4. both in parallel
    Answer and solution

    Answer: A

    The ammeter must carry the same current as the resistor, so it is in series. The voltmeter reads the potential difference across the resistor, so it is in parallel.
  9. MCQWarm-up

    A Zener diode is used as a voltage regulator when it is
    1. forward biased
    2. unbiased
    3. reverse biased below breakdown
    4. reverse biased and operating in breakdown
    Answer and solution

    Answer: D

    A Zener holds its voltage nearly constant in the reverse breakdown region, so it is operated reverse biased, beyond the breakdown voltage.
  10. MCQWarm-up

    The forward knee (cut-in) voltage of a silicon junction diode is about
    1. 0.3 V
    2. 2.0 V
    3. 0.7 V
    4. 5.0 V
    Answer and solution

    Answer: C

    Silicon starts to conduct noticeably near 0.7 V; germanium near 0.3 V.
  11. MCQWarm-up

    A graph of potential difference V (y-axis) against current I (x-axis) for a metal wire at constant temperature is a straight line through the origin. Its slope gives
    1. the power
    2. the resistance
    3. the resistivity
    4. the conductance
    Answer and solution

    Answer: B

    V=IR, so the slope V/I is the resistance R. The conductance would be the slope of the I–V graph.
  12. MCQWarm-up

    With a concave mirror, the object pin is moved until its image is at the same place as the object. The pin is then at
    1. the centre of curvature
    2. the focus
    3. the pole
    4. infinity
    Answer and solution

    Answer: A

    An object at the centre of curvature has its real, inverted image of equal size at the same place. So u=v=R=2f.
  13. MCQWarm-up

    The pitch of a screw gauge is the
    1. distance between two circular divisions
    2. diameter of the screw
    3. smallest length the gauge can read
    4. distance the screw moves along its axis in one full turn
    Answer and solution

    Answer: D

    Pitch is the linear distance moved per rotation. The least count is pitch divided by the number of circular divisions.
  14. NATWarm-up

    A length is read as 5.0 cm with an absolute error of 0.1 cm. Find the percentage error.
    Answer and solution

    Answer: 2 %

    Percentage error =(0.1/5.0)×100=2%.
  15. MCQWarm-up

    The least count of an ordinary metre scale marked in millimetres is
    1. 1 cm
    2. 0.01 cm
    3. 0.1 cm
    4. 0.5 cm
    Answer and solution

    Answer: C

    The smallest division is 1 mm =0.1 cm.
  16. MCQWarm-up

    In a resonance tube experiment (ignoring end correction), the first resonance occurs when the air column length is
    1. λ/2
    2. λ/4
    3. 3λ/4
    4. λ
    Answer and solution

    Answer: B

    The closed end is a node and the open end is nearly an antinode. The shortest such column is a quarter wavelength.
  17. MCQWarm-up

    At the position of minimum deviation of a prism, the ray inside the prism is
    1. parallel to the base
    2. perpendicular to the base
    3. along the normal to the first face
    4. along the second face
    Answer and solution

    Answer: A

    At minimum deviation i=e and r1=r2=A/2. The path is symmetrical, so the ray inside travels parallel to the base of the prism.
  18. MCQWarm-up

    Water rises higher in a capillary tube of
    1. larger radius
    2. greater length of tube above the water
    3. greater mass
    4. smaller radius
    Answer and solution

    Answer: D

    h=2Tcos⁡θ/(rρg). So h∝1/r and a thinner tube gives a higher rise.
  19. MCQWarm-up

    The wire of a metre bridge is made of an alloy such as manganin or constantan because the alloy
    1. has very high resistivity so it never heats
    2. has zero resistance
    3. has a very small temperature coefficient of resistance
    4. is magnetic
    Answer and solution

    Answer: C

    A small temperature coefficient keeps the resistance per unit length steady, even if the wire heats slightly. A uniform wire is needed so that resistance is proportional to length.
  20. MCQWarm-up

    A steel ball falls at terminal velocity in a viscous liquid. At that stage the net force on it is
    1. equal to its weight
    2. zero
    3. equal to the viscous force
    4. upward and increasing
    Answer and solution

    Answer: B

    At terminal velocity, weight is balanced by the upthrust plus the viscous drag, so the net force is zero and the acceleration is zero.
  21. MCQWarm-up

    In Searle's method for Young's modulus, a second (reference) wire carrying a constant load is used mainly to
    1. cancel the effect of temperature change and sagging of the support
    2. double the extension
    3. apply the test load
    4. measure the diameter
    Answer and solution

    Answer: A

    Both wires hang from the same rigid support. Changes in temperature or small movements of the support affect both wires alike, so the vernier measures only the extra extension of the test wire.
  22. MCQWarm-up

    The SI unit of specific heat capacity is
    1. JK−1
    2. Jkg
    3. kgKJ−1
    4. Jkg−1K−1
    Answer and solution

    Answer: D

    c=Q/(mΔT), which has unit J per kg per K. JK−1 is heat capacity.
  23. NATStandard

    A vernier calliper has least count 0.01 cm. For a cylinder the main scale reads 2.4 cm and the 6th vernier division coincides with a main scale division. The zero error is +0.02 cm. Find the correct diameter in cm.
    Answer and solution

    Answer: 2.44 cm (±0.001)

    Observed reading = MSR + VSR × LC =2.4+6×0.01=2.46 cm. Correct reading = observed − zero error =2.46−0.02=2.44 cm.
  24. NATStandard

    A vernier calliper has 10 vernier divisions and LC 0.01 cm. With the jaws closed, the 8th vernier division coincides with a main scale division, so the zero error is negative. For a block, the main scale reads 3.1 cm and the 5th vernier division coincides. Find the correct length in cm.
    Answer and solution

    Answer: 3.17 cm (±0.001)

    Closed jaws: the vernier zero is behind the main zero by (10−8) divisions, so zero error =−(10−8)×0.01=−0.02 cm. Observed =3.1+5×0.01=3.15 cm. Correct =3.15−(−0.02)=3.17 cm.

    Why people get this wrong: With a negative zero error you count from the other end of the vernier: 8 coinciding means −2, not −8.

  25. NATStandard

    A screw gauge has pitch 1 mm and 100 circular divisions. For a wire the main scale shows 3 mm and the circular scale reads 36. With the jaws closed the circular reading is 97 (the zero is below the reference line by 3 divisions, a negative zero error). Find the correct diameter in mm.
    Answer and solution

    Answer: 3.39 mm (±0.001)

    LC =1/100=0.01 mm. Observed =3+36×0.01=3.36 mm. Closed reading 97=100−3, so zero error =−3×0.01=−0.03 mm. Correct =3.36−(−0.03)=3.39 mm.
  26. NATStandard

    A screw gauge has pitch 0.5 mm and 50 circular divisions. With the jaws closed the circular scale reads +4. For a sphere the main scale reads 2.5 mm and the circular scale reads 27. Find the correct diameter in mm.
    Answer and solution

    Answer: 2.73 mm (±0.001)

    LC =0.5/50=0.01 mm. Observed =2.5+27×0.01=2.77 mm. Zero error =+4×0.01=+0.04 mm. Correct =2.77−0.04=2.73 mm.
  27. MCQStandard

    When the jaws of a screw gauge are closed, the zero of the circular scale is 4 divisions above the reference line (LC =0.01 mm). The zero error is
    1. +0.04 mm
    2. −0.96 mm
    3. −0.04 mm
    4. +0.96 mm
    Answer and solution

    Answer: C

    If the circular zero has not yet reached the reference line (it is above it), the screw has to be turned further to close fully, so the gauge reads less than it should: the zero error is negative, −4×0.01=−0.04 mm. If the zero were below the line, the error would be positive.

    Why people get this wrong: Above the line means negative; below means positive. Do not confuse this with the reading of the circular scale.

  28. NATStandard

    In a simple pendulum experiment a graph of T2 (y-axis, in s2) against L (x-axis, in m) is a straight line passing through (0.20,0.80) and (1.00,4.00). Find g in ms−2 from the slope.
    Answer and solution

    Answer: 9.87 m/s² (±0.05)

    T2=4π2gL, so slope =4π2/g. Slope =(4.00−0.80)/(1.00−0.20)=4.0 s2/m. Then g=4π2/4.0=9.87 ms−2.
  29. NATStandard

    The length of the thread of a pendulum is 90.0 cm and the bob has diameter 2.0 cm. The time for 20 oscillations is 38.2 s. Find g in ms−2 (give 2 decimals; π2=9.8696).
    Answer and solution

    Answer: 9.84 m/s² (±0.03)

    L=90.0+1.0=91.0 cm =0.910 m. T=38.2/20=1.91 s. g=4π2L/T2=39.478×0.910/3.6481=9.847. So g≈9.85 (tolerance covers rounding).

    Why people get this wrong: Forgetting to add the bob radius to the thread length.

  30. MCQStandard

    Why is the time of 20 or more oscillations measured instead of one?
    1. The period increases with the number of oscillations
    2. The error in T falls because the stopwatch error is shared among many oscillations
    3. A single oscillation never has a fixed period
    4. The thread length changes after one swing
    Answer and solution

    Answer: B

    The stopwatch has a fixed error (reaction time plus least count) in t. With n oscillations T=t/n, so ΔT=Δt/n is smaller. The relative error ΔT/T=Δt/t also becomes smaller as t gets larger.

← All topics