Wheel nut torque: typical values, N·m to lbf·ft, push on the brace and star tightening order

See a typical wheel nut torque for your kind of vehicle or stud size, or type your handbook figure; convert N·m, lbf·ft and kgf·m; work out how hard to push on a brace of any length; and see the star order to tighten 4, 5, 6 or 8 nuts.

Keep it one tap away for everyday use.

Bookmark Wheel nut torque?

Press Ctrl + D now. Your browser opens its own bookmark box, where you choose the name and folder.

Or install fibub as an app: every tool you open then works offline.

  1. Torque
  2. Brace push
  3. Star order
Nothing is uploadedWorks offline once open

1. How tight?

The right figure is printed in your vehicle's handbook (often in the "wheels and tyres" or "technical data" pages) and sometimes on a sticker. Typical ranges here are rounded from many makers' handbooks: they are a sanity check, and your handbook value wins.

2. Push on the brace

Measure from the centre of the nut to where your hand or foot pushes. Push at right angles to the handle.

3. Tightening order

Go round twice: first snug every nut in this order with the wheel just touching the ground, then do them all to the full torque in the same order. Going across the wheel pulls it on flat against the hub.

Good habits

  • Re-check the nuts with a torque wrench after 50 to 100 km (30 to 60 miles), as the wheel beds in. Tyre shops ask for this after fitting alloy wheels.
  • Keep threads clean and dry. Do not oil or grease them unless the handbook says so: oiled threads reach the same torque with much more clamp, and can stretch the studs.
  • Do not do the final tightening with an impact gun. Too tight can stretch studs and warp brake discs; too loose and a wheel can come off.
  • Never jump on the brace. If the push you need is more than about half your body weight, use a longer bar or a torque wrench, or ask a tyre shop.

Nothing you type leaves this page. For study and planning: always follow your vehicle maker's figure and method.

What it does

Wheel nuts (or wheel bolts) have to be tight enough that the wheel cannot work loose, but not so tight that the studs stretch or the brake disc warps. Car makers give a figure, called the torque, in newton metres (N·m) or pound-feet (lbf·ft). This tool helps you use that number when all you have is the wheel brace from the boot. Pick your kind of vehicle or the stud thread to see a typical range, or type the figure from your handbook. The tool converts it between N·m, lbf·ft and kgf·m, works out how hard to push on a brace of your length, compares that with your body weight, and draws the star order to tighten 4, 5, 6 or 8 nuts.

It goes with the change a flat tyre lesson, and with tyre pressure to set the spare’s pressure afterwards; for bolts in machines and joints, use bolt torque.

How to use it

  1. How tight? Choose “My handbook value” and type the torque from your handbook, or pick a kind of vehicle or a stud thread to see a typical range. The middle of the range is filled in, but your handbook value always wins.
  2. Push on the brace. Measure the brace from the centre of the nut to where you push, and type it in cm or inches. Add your weight if you want a feel for how hard that is.
  3. Tightening order. Choose how many nuts the wheel has. Follow the numbers on the picture, twice round: snug first, then full torque.

What each number means

  • Torque (N·m, lbf·ft, kgf·m): the turning effect on the nut. 1 lbf·ft is about 1.36 N·m; 1 kgf·m is about 9.81 N·m.
  • Brace length: the lever. Torque = push × length, so a brace twice as long needs half the push.
  • Push (N, kgf, lbf): the force at right angles to the handle at the point you measured to. 1 kgf is the weight of 1 kg, about 9.81 N.
  • Share of body weight: a rough feel. If it is more than about half, use a longer bar or a torque wrench instead of bouncing on the brace.
  • Star order: the order to tighten the nuts, going across the wheel so it pulls on evenly.

Worked example

Your handbook says 110 N·m. That is 110 ÷ 1.3558 = 81.1 lbf·ft, or 110 ÷ 9.807 = 11.2 kgf·m. Your brace is 40 cm (0.40 m) from the nut to your hand, so the push is 110 ÷ 0.40 = 275 N, which is 275 ÷ 9.807 = 28.0 kgf or 61.8 lbf. For a 70 kg person (about 687 N), that is about 40 % of body weight: a firm lean, not a jump. On five nuts, numbered clockwise from the top, you tighten 1, 3, 5, 2, 4.

FAQs

Is a brace and my weight as good as a torque wrench? No, it is an estimate: you may not push exactly at right angles or at exactly the length you measured. It gets you close at the roadside. Check with a torque wrench as soon as you can.

Why does the typical range matter if the handbook wins? It catches mistakes, such as reading 110 lbf·ft as 110 N·m (that is 149 N·m, a big difference) or using a figure meant for a different vehicle.

Should I re-check the nuts? Yes, after 50 to 100 km (30 to 60 miles), especially with alloy wheels or new wheels, as the wheel beds in.

Should I oil the threads? Not unless the handbook says so. Torque figures are for clean, dry threads; oil lets the same torque clamp much harder.

Where the numbers come from

  • Conversions: 1 lbf·ft = 1.3558 N·m, 1 kgf·m = 9.80665 N·m, 1 lbf = 4.4482 N, 1 in = 2.54 cm. Push force F = T / L (torque divided by the lever length, pushing at right angles).
  • Typical torque ranges are rounded by fibub from the spread of figures printed in car, SUV, pickup and trailer makers' handbooks for each kind of vehicle and stud thread. They are a sanity check only: always use the value in your own vehicle's handbook. Checked 2026-11-16.
  • Star tightening order and the advice to re-check after 50 to 100 km follow general guidance from vehicle handbooks and tyre fitters. Drawings are fibub's own.

Standard scientific values, such as constants, atomic weights and melting points, are facts found in every textbook; we name where ours were checked. If you are an author or publisher and want a value, a credit or a table changed or removed, tell us and we will act quickly.

Last updated 2026-11-16.

Change log for Wheel nut torque

  1. Tyres and punctures: #L371 plug a tyre puncture, #L372 fix a bike puncture, #T1010 wheel nut torque Details on GitHub

Every change to fibub

Related tools

Bolt torque #T439 Work out the tightening torque for a target bolt preload (or the preload a torque gives) with the nut factor T = K F d or the thread and under-head friction split, the tensile stress area of ISO metric or UNC/UNF threads from the pitch, the bolt and clamped-part stiffness, the joint constant, the separation load and safety factors, with a joint diagram. Tyre pressure #T898 Convert tyre pressure between psi, bar and kPa, see how temperature changes it, and find what to fill to today so the tyre is right on a hotter or colder day. Tyre size #T940 Type the size printed on your tyre, like 205/55 R16 91V, and see in plain words how wide and tall it is, what wheel it fits, how much weight it carries and how fast it is rated, with a picture of each part. Change a flat tyre #L370 Change a flat car tyre onto the spare in eight illustrated steps: get safe, loosen the nuts, jack at the right point, swap the wheel and tighten in a star pattern. Tick each step, name the parts, and print the checklist for your glovebox. Plug a tyre puncture #L371 Plug a nail or screw hole in a tubeless car tyre with a string plug kit in eight illustrated steps, check first whether the hole can be repaired at all, and learn why most tyre makers treat an outside plug as a temporary fix. Levers in everyday tools #L382 See why a claw hammer pulls nails, a long wheel brace undoes tight nuts and a wheelbarrow carries 80 kg. Slide your hand along the handle and watch the push you need change, sort tools into class 1, 2 and 3 levers, and check the principle of moments.