Op-amp circuits
Electronics · 82 questions and templates for GATE Physics, in order from warm-up to top rank. Check each answer, then read the full solution.
New to this topic? Read the lesson first: Op-amp circuits.
Loading questions… (they need JavaScript; nothing you type is sent anywhere)
Written questions with solutions
The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.
-
MCQWarm-up
For an ideal op-amp working with negative feedback (output not saturated), the two rules used to analyse the circuit are- the output current is zero and the output voltage is zero
- the inputs draw no current and the output resistance is infinite
- the inputs draw no current and the two input voltages are equal
- the input voltages differ by the supply voltage
Answer and solution
Answer: C
Infinite input resistance means no current into either input. Infinite open-loop gain with a finite output means : the feedback forces the inputs to the same voltage (a virtual short). The second rule fails if there is no negative feedback or if the output saturates.Why people get this wrong: The virtual short is a result of negative feedback, not a property of the chip; a comparator has none.
-
MCQWarm-up
An op-amp is used open loop as a comparator. With V and V, the output is- at the negative saturation level
- at the positive saturation level
- about V
- zero, because the inputs are nearly equal
Answer and solution
Answer: A
Open loop, V. With that is far beyond the rails, so the output sits at . There is no feedback to make the inputs equal.Why people get this wrong: Applying the virtual-short rule to a circuit with no negative feedback.
-
MCQWarm-up
A photodiode feeds a current of A into the inverting input of an op-amp whose non-inverting input is grounded; a k resistor connects output to inverting input. The output voltage is- V
- V
- V
- V
Answer and solution
Answer: D
The inverting input is a virtual ground, so the photodiode sees zero bias and all its current flows on through the feedback resistor: V. This current-to-voltage converter is a transimpedance amplifier.Why people get this wrong: The sign: current flowing into the node must leave through towards the output, so the output goes negative.
-
NATWarm-up
An op-amp with input offset voltage mV is used in a non-inverting amplifier with k and k. With the input grounded, the output offset is ______ mV (bias currents ignored).Answer and solution
Answer: 202 mV (±1)
The offset acts like a small voltage source in series with the non-inverting input, and it is amplified by the noise gain : mV. This is the same for the inverting configuration with the same resistors.Why people get this wrong: Using the inverting gain gives 200 mV; offsets always see the noise gain.
-
MCQWarm-up
A precision ("super-diode") half-wave rectifier places the diode inside the op-amp's feedback loop. Why can it rectify a mV signal?- The op-amp heats the diode so it conducts at lower voltage
- The diode's forward drop is divided by the open-loop gain, so the effective threshold is microvolts
- The op-amp output is always exactly zero
- A Schottky diode is required, whose drop is zero
Answer and solution
Answer: B
When the diode conducts the loop is closed and the output follows the input exactly; the op-amp output simply rises a diode drop higher than the load. The input needed to start conduction is about , a few microvolts.Why people get this wrong: The diode still drops 0.6 V; the op-amp supplies it.
-
MSQWarm-up
Which statements about an op-amp Schmitt trigger are correct?- Its switching thresholds for rising and falling inputs differ (hysteresis)
- It uses positive feedback
- It gives a clean single transition for a slow, noisy input if the noise is smaller than the hysteresis
- Its two inputs stay at equal voltages at all times
Answer and solution
Answer: A, B, C
Feedback to the non-inverting input makes the threshold depend on the output state, so once it has switched the input must move back past the other threshold. Noise smaller than the gap cannot cause chatter. With positive feedback the output sits at a rail and the inputs are generally not equal.Why people get this wrong: The virtual short belongs to negative feedback only.
-
MCQWarm-up
An ideal inverting summing amplifier has feedback resistor k. Input V enters through k and input V through k. The output is- V
- V
- V
- V
Answer and solution
Answer: B
The inverting input is a virtual ground, so each input sends into the summing node: mA. All of it flows through : V.Why people get this wrong: Adding the input voltages directly ( V) ignores that the k input is weighted twice as strongly.
-
NATStandard
An inverting Schmitt trigger takes its input on the inverting terminal. The non-inverting terminal is joined to a V reference through k and to the output through k. The output saturates at V. The upper threshold voltage is ______ V.Answer and solution
Answer: 3 V (±0.01)
By superposition, . With V, V: the input must rise above 3.0 V to switch the output low. With V the lower threshold is V; hysteresis 4.0 V centred on 1.0 V.Why people get this wrong: The centre of the window is V, not the reference itself.
-
NATStandard
An op-amp astable multivibrator has k and F in its timing path, and a feedback divider giving (symmetric output). Its frequency is ______ Hz (to the nearest whole number).Answer and solution
Answer: 455 Hz (±2)
The capacitor charges towards and the output flips when it reaches . Each half period lasts , so ms and Hz.Why people get this wrong: Forgetting the factor 2 (two half periods) doubles the frequency.
-
MCQStandard
A 555 timer in astable mode has k, k and F. Its frequency is about- 1.37 kHz
- 686 Hz
- 343 Hz
- 6.9 kHz
Answer and solution
Answer: B
The capacitor charges through and discharges through , between and ; each takes time constants. ms, so Hz. Duty cycle .Why people get this wrong: Using in both halves gives 1.31 kHz-type answers.
-
MCQStandard
An inverting first-order low-pass filter has input resistor k, and k in parallel with nF in the feedback path. Its DC gain and cut-off frequency are- and about 1 kHz
- and about 10 kHz
- and about 1 kHz
- and about 6.3 kHz
Answer and solution
Answer: A
DC gain . The pole is set by the feedback pair: kHz. The input resistor does not enter the cut-off.Why people get this wrong: Using the input resistor with gives 10 kHz.
-
MCQStandard
A log amplifier uses a transistor in the feedback path, giving . At 300 K, each tenfold increase of the input changes the output by about- mV
- V
- V
- mV
Answer and solution
Answer: D
mV per decade. The scale is temperature dependent, so practical log amps compensate and cancel with a matched second transistor.Why people get this wrong: 26 mV is a factor , not 10.
-
MCQStandard
A three-op-amp instrumentation amplifier has first-stage resistors k on each side, gain resistor between them, and a unity-gain difference stage. Its differential gain is- 50
- 98
- 49
- 99
Answer and solution
Answer: D
The input followers force the input difference across , and the same current flows through both , so the first stage gives . The difference stage multiplies by 1.Why people get this wrong: Missing the 2 (both resistors carry the current) gives 50; missing the 1 gives 98.
-
MSQStandard
A first-order op-amp all-pass (phase-shift) circuit has transfer function . Which statements are correct?- at every frequency
- Its phase goes from to as frequency rises
- At the phase is
- It amplifies one band of frequencies selectively
Answer and solution
Answer: A, B, C
Numerator and denominator have equal magnitudes, so . The phase is : 0 at DC, at , at high frequency. It changes only phase: useful for phase equalisation and quadrature oscillators.Why people get this wrong: An all-pass filter passes all frequencies equally; its job is the phase.
-
MCQStandard
A balanced Howland current pump is driven by and has its four resistors chosen so the load current is . Its main property is that the load current- depends on the load as
- is independent of the load resistance (within the output swing), and the load can be grounded
- is limited to zero for grounded loads
- flows only when is negative
Answer and solution
Answer: B
Positive and negative feedback balance so the output resistance seen by the load is infinite: for any as long as the op-amp does not saturate. Unlike a simple floating-load V-to-I converter, the load can return to ground.Why people get this wrong: Any resistor mismatch makes the output resistance finite (even negative).
-
NATStandard
An ideal op-amp integrator ( k, F) is driven by a symmetric V square wave of frequency kHz with no DC component. The peak-to-peak amplitude of the triangular output is ______ V.Answer and solution
Answer: 0.5 V (±0.005)
During each half period the input is constant, so the output ramps at V/s for ms: a change of V. The output swings 0.5 V peak to peak.Why people get this wrong: Using the full period gives 1 V.
-
MCQStandard
Why is a plain op-amp differentiator (capacitor in, resistor in feedback) rarely used without changes?- Its gain falls with frequency, so it loses signal
- It needs a negative supply only
- It cannot pass DC
- Its gain rises with frequency, so it amplifies high-frequency noise and tends to ring or oscillate
Answer and solution
Answer: D
grows without limit until the op-amp's own roll-off adds a second pole, giving a resonant peak. A small resistor in series with the input capacitor (and often a capacitor across ) limits the high-frequency gain.Why people get this wrong: Not passing DC is the point of a differentiator, not a flaw.
-
MCQStandard
An inverting amplifier with an ideal op-amp has k and k. It is driven by a signal source whose internal resistance is k. The gain from the source's open-circuit voltage to the output isAnswer and solution
Answer: C
The input resistance of an inverting amplifier is only , because the inverting input is a virtual ground. The source resistance adds in series: the current is , so . A non-inverting stage or a buffer in front would avoid this loss.Why people get this wrong: Treating the amplifier's input resistance as infinite, as for a non-inverting amplifier.
-
NATStandard
Two voltages, V and V, are each connected through a k resistor to the non-inverting input of an ideal op-amp (nothing else is connected to that input). The op-amp has k from its inverting input to ground and k from the output to its inverting input. The output is ______ V.Answer and solution
Answer: 6 (±0.01)
No current enters the non-inverting input, so the two equal resistors average the inputs: V (superposition, or Millman's theorem). The stage has gain , so V.Why people get this wrong: Applying the gain to the sum V, as if it were an inverting summer, gives V.
-
MCQStandard
In a series voltage regulator an op-amp drives a pass transistor so that a fraction of the output, taken from a divider with k (output to feedback node) and k (feedback node to ground), equals a V reference at the other op-amp input. The regulated output is- V
- V
- V
- V
Answer and solution
Answer: D
The loop forces the divided output to equal the reference: V, so V. The circuit is a non-inverting amplifier of the reference, with the transistor supplying the load current.Why people get this wrong: V uses instead of .
-
MCQStandard
Two log amplifiers produce outputs proportional to and (with ). Their outputs are added by a summing amplifier, and the sum drives an antilog (exponential) amplifier. Apart from a constant scale factor, the final output is proportional toAnswer and solution
Answer: A
, and the antilog stage undoes the logarithm, giving an output . This is an analogue multiplier; replacing the adder by a difference amplifier would divide instead. The inputs must stay positive, since a log amplifier only works in one quadrant.Why people get this wrong: would need a subtractor, not an adder, before the antilog stage.
-
NATExam level
A non-inverting amplifier is designed for a gain of () using an op-amp with open-loop gain . Its actual gain is ______ (to two decimal places).Answer and solution
Answer: 48.78 (±0.02)
With : , that is . The error, 2.4%, is about the ideal gain divided by .Why people get this wrong: Assuming the ideal gain 50 when the loop gain is only 40.
-
NATExam level
An op-amp with gain-bandwidth product MHz is used as an inverting amplifier of gain . Its closed-loop dB bandwidth is ______ kHz.Answer and solution
Answer: 100 kHz (±0.5)
The bandwidth is set by the feedback factor , i.e. by the noise gain , not by the signal gain 9: kHz.Why people get this wrong: Dividing by the signal gain gives 111 kHz.
-
MCQExam level
An inverting amplifier uses k and k. To cancel the output error caused by equal input bias currents, the resistor from the non-inverting input to ground should be- 9 kΩ
- 100 kΩ
- 10 kΩ
- 90 kΩ
Answer and solution
Answer: A
With the input grounded, the inverting input sees to ground (through the source and the output, both low impedance). Equal bias currents then make equal voltages at the two inputs if k. What remains is set by the offset current.Why people get this wrong: Using or alone.
-
NATExam level
An inverting amplifier has M with the correct bias-compensation resistor fitted. The op-amp has bias current nA and offset current nA. The worst-case output error from these currents is ______ mV.Answer and solution
Answer: 10 mV (±0.1)
Without compensation the error would be mV. The compensation resistor cancels the common part of the bias currents, leaving only their difference: mV.Why people get this wrong: Quoting 100 mV, the uncompensated error.
-
MCQExam level
A unity-gain Sallen-Key low-pass filter has two equal resistors; the capacitor from the middle node to the output is and the capacitor from the non-inverting input to ground is . Its quality factor is- 0.5
- 0.707
- 1.0
- 1.414
Answer and solution
Answer: B
For the unity-gain Sallen-Key low-pass the denominator is , so . With equal : , a Butterworth response.Why people get this wrong: Swapping the capacitors gives .
-
NATExam level
An equal-component Sallen-Key low-pass filter (equal , equal ) has a non-inverting amplifier of gain , giving . For a Butterworth response, must be ______ (to three decimal places).Answer and solution
Answer: 1.586 (±0.002)
Butterworth needs , so and . At the poles reach the imaginary axis and the filter oscillates.Why people get this wrong: Setting .
-
MSQExam level
An op-amp astable multivibrator uses an path to the inverting input and a resistive divider (fraction ) to the non-inverting input, with symmetric output levels . Which statements are correct?- The output is a square wave
- The capacitor voltage swings between and
- The period does not depend on
- The duty cycle is 25%
Answer and solution
Answer: A, B, C
The capacitor charges towards the output level until it crosses the threshold , then the output flips. Each half takes , a ratio in which cancels. With symmetric levels both halves are equal: 50% duty.Why people get this wrong: Thinking a bigger supply makes it faster: both the threshold and the target scale together.
-
NATExam level
A log amplifier gives with k, A and mV. For V, is ______ V (to three decimal places).Answer and solution
Answer: 0.595 V (±0.003)
. . V.Why people get this wrong: Using gives 0.26 V.
-
MCQExam level
A super-diode (op-amp follower with a diode inside the loop, load resistor to ground, non-inverting configuration) receives mV and then mV. The outputs across the load are- 0 V and mV
- 0 V in both cases, because 50 mV is below the diode drop
- mV and 0 V
- mV and mV
Answer and solution
Answer: C
For positive input the op-amp drives the diode on and the loop forces the load voltage to equal the input: mV. For negative input the diode is reverse biased, the loop opens, and the load is pulled to 0 V (the op-amp output swings to its negative rail, which is why fast precision rectifiers add a second diode).Why people get this wrong: The diode drop is hidden inside the loop; it does not appear at the output.