Home / Learn / Exam prep / GATE Physics / Lesson 9.3
All lessons

Module 9: Electronics · Lesson 9.3 · about 45 min

Op-amp circuits

Op-amp circuits at GATE depth: the two golden rules and the noise gain, inverting, non-inverting, summing, difference and instrumentation amplifiers, integrators, differentiators and active filters, real limits (gain-bandwidth product, slew rate, offset voltage and bias currents), and non-linear circuits: comparators, Schmitt triggers, precision rectifiers, log amplifiers and the astable multivibrator.

Key points, meanings and formulas on one page: choose "Save as PDF" in the print box.

Module 9 · about 45 minutes. The JAM op-amps lesson covers the standard amplifiers. GATE adds the non-ideal limits and the non-linear circuits, and expects you to see each one as the feedback system of lesson 9.2 with a huge forward gain.

With negative feedback and a very large gain, the op-amp does whatever it must at its output to make its two inputs equal. Every linear circuit follows from that and from "no current into the inputs". Remove the negative feedback, or add positive feedback, and the same chip becomes a comparator, a memory (Schmitt trigger) or an oscillator.

1. Linear circuits

The golden rules (ideal op-amp, negative feedback, output not saturated): V+=V−, and no current flows into either input. Write KCL at the inverting input and the gain drops out.

Circuit Output Input resistance
inverting −RfR1Vin R1
non-inverting (1+RfR1)Vin very high
summing (inverting) −Rf(V1R1+V2R2+⋯) Rk for input k
difference (matched ratio R2/R1) R2R1(V2−V1) unequal at the two inputs
instrumentation (three op-amps) (1+2RRG)R3R2(V2−V1) very high at both
integrator −1RC∫Vindt R
differentiator −RCdVindt falls with frequency

Worked examples. A difference amplifier with R1=10 kΩ, R2=100 kΩ gives 10(V2−V1); a 1% mismatch in one resistor lets a common-mode signal through with gain of order 0.01×R2/(R1+R2)≈0.009, so CMRR is only about 60 dB. That is why the instrumentation amplifier, whose gain is set by one resistor RG and whose first stage passes common-mode signals at unity gain, is used for small differential signals. An integrator with R=10 kΩ and C=0.1 µF fed a 1 V step ramps at −1000 V/s and reaches −10 V after 10 ms. A real integrator needs a large resistor across C, or its own offset ramps it into saturation.

Active filters. A resistor Rf in parallel with C in the feedback path of an inverting amplifier makes a first-order low-pass with DC gain −Rf/R1 and corner 1/2πRfC. Second-order sections such as the Sallen-Key low-pass place the poles anywhere: with equal resistors R and capacitors C and amplifier gain K, ω0=1/RC and Q=1/(3−K). At K=3 the poles reach the imaginary axis: the same condition as the Wien oscillator of lesson 9.4.

2. Real op-amps

noise gain `$1 + R_f/R_1$`
the gain `$1/\beta$` seen by the loop; it sets bandwidth, offset errors and stability, whatever the signal gain is (the inverting amplifier's signal gain is `$-R_f/R_1$`, one less in size)
gain-bandwidth product
an internally compensated op-amp has one dominant pole, so closed-loop bandwidth = GBW/(noise gain)
slew rate SR
the largest `$dV_{out}/dt$` the output can manage (a fixed current charging the compensation capacitor); full-power bandwidth `$f_p = \text{SR}/2\pi V_p$`
input offset voltage `$V_{os}$`
a small voltage in series with one input; appears at the output multiplied by the noise gain
bias current `$I_B$`
flows into each input; through `$R_f$` it makes an error `$I_BR_f$`, cancelled to first order by putting `$R_1\parallel R_f$` in series with the + input, leaving only the offset current `$I_{os}R_f$`

Worked example. An op-amp with GBW = 1 MHz, SR = 0.5 V/µs and Vos=2 mV is used as a non-inverting amplifier of gain 101. Bandwidth: 1 MHz/101 ≈ 9.9 kHz. Output offset: 2 mV × 101 = 0.20 V. Full-power bandwidth at 10 V peak: 0.5×106/(2π×10)=8.0 kHz. Above that a sine output turns into a triangle, whatever the small-signal bandwidth says.

3. Non-linear circuits

Comparator. No feedback: the output saturates at +Vsat when V+>V− and at −Vsat otherwise. A noisy input near the threshold makes it chatter.

Schmitt trigger. Positive feedback through a divider gives two thresholds. For the inverting form (input on −, divider R1 to a reference, R2 to the output):

VT±=VrefR2±VsatR1R1+R2,ΔVH=2VsatR1R1+R2

The output remembers which threshold it last crossed: the circuit has two stable states, and noise smaller than ΔVH cannot make it chatter.

Precision rectifier (super-diode). A diode inside the feedback loop: the op-amp raises its output by one diode drop more than needed, so the circuit rectifies millivolt signals that an ordinary diode would ignore. Adding a second stage gives a precision full-wave rectifier (absolute-value circuit).

Log and antilog amplifiers. A diode or transistor in the feedback path of an inverting amplifier:

Vout=−VTln⁡VinRIs

Each decade of input changes the output by VTln⁡10=59.5 mV at 300 K. Swap the diode and the resistor for an exponential (antilog) amplifier; log, add and antilog to multiply. Is and VT both depend on temperature, so real log amps use matched pairs.

Transfer curves V_out against V_in for six op-amp circuits with the output limited at ±12 V. Choose the Schmitt trigger and sweep the input up and down to trace its hysteresis loop; choose the log amplifier to see a straight line on a logarithmic input axis.

Astable multivibrator. A Schmitt trigger whose own output charges a capacitor on its inverting input through R. The capacitor swings between ±βVsat with β=R1/(R1+R2), and each half period is the time to charge from −βVsat to +βVsat towards +Vsat:

T=2RCln⁡1+β1−β=2RCln⁡(1+2R1R2)

For R1=0.86R2, ln⁡(2.72)≈1 and T≈2RC. A monostable adds a diode that clamps the capacitor in one state, so a trigger pulse produces one output pulse of fixed length. The 555 timer does the same jobs with two comparators and thresholds at VCC/3 and 2VCC/3: T=0.693(RA+2RB)C.

“V₊ = V₋ always holds for an op-amp.” It holds only with negative feedback, inside the linear range. In a comparator or Schmitt trigger the inputs differ by volts and the output sits at a rail. Even with negative feedback the rule fails when the output saturates or the signal changes faster than the slew rate allows: then the loop is broken and the inputs separate.

  • Golden rules: V+=V− and no input current, only with negative feedback in the linear range.
  • Inverting −Rf/R1, non-inverting 1+Rf/R1, difference (R2/R1)(V2−V1), integrator −1RC∫Vdt.
  • Bandwidth = GBW/noise gain; offset at output = Vos× noise gain; fp=SR/2πVp.
  • Schmitt: thresholds (VrefR2±VsatR1)/(R1+R2), width 2VsatR1/(R1+R2).
  • Log amp: 59.5 mV per decade at 300 K; astable T=2RCln⁡(1+2R1/R2); 555 astable 0.693(RA+2RB)C.

Practise: exam questions on this lesson

Next: lesson 9.4 turns the stability question round and builds oscillators on purpose. The op-amp calculator works out gains and resistor values for the standard circuits.

Check yourself

1An op-amp with a gain-bandwidth product of 2 MHz is used as an inverting amplifier with gain −9. Its closed-loop bandwidth is about
2An op-amp with slew rate 1 V/µs must deliver an undistorted sine of 5 V peak. The highest frequency it can reproduce is about
3In an inverting Schmitt trigger with ±10 V output and feedback divider R₁ = 1 kΩ (to ground), R₂ = 9 kΩ (to the output), the hysteresis width is

Sources

  • A. S. Sedra and K. C. Smith, Microelectronic Circuits, 7th ed. (2015), chapters 2 and 17
  • P. Horowitz and W. Hill, The Art of Electronics, 3rd ed. (2015), chapters 4 and 5
  • S. Franco, Design with Operational Amplifiers and Analog Integrated Circuits, 4th ed. (2015), chapters 1 to 6
  • GATE Physics (PH) syllabus, Electronics section, published by the organising IIT each year

Your ticks stay in this browser. Save them as a file on the course home.

Updated 2026-11-22. Not affiliated with the IITs, IISc or the GATE organising institute. The general aptitude part of GATE is not covered here. Check the official GATE website for the current pattern. All questions are original.