How to screw wood together without splitting it: pilot holes, clearance holes and screw length

Join two pieces of wood with screws that pull tight and do not split the wood: pick the screw length, drill a clearance hole and a pilot hole, countersink, set the drill's clutch and drive straight. The screw picker suggests length, gauge and drill sizes.

Keep it one tap away for everyday use.

Bookmark Drill and screw wood?

Press Ctrl + D now. Your browser opens its own bookmark box, where you choose the name and folder.

Or install fibub as an app: every tool you open then works offline.

  1. Pick screw
  2. Drill holes
  3. Drive
Nothing is uploadedWorks offline once open

Stay safe

  • Wear safety glasses. Drills throw out chips and a snapped bit can fly.
  • Clamp small pieces. If a bit catches, the drill can spin the wood round and hit your hand.
  • Take out the battery or unplug the drill before you change a bit. Tie back long hair and loose sleeves.
  • Never drill into a wall here without checking for cables and pipes first: see the Wall fixings course.

What you need

  • Drill driver
  • Wood drill bits
  • Countersink bit
  • Screwdriver bits (PZ2, PH2, Torx)
  • Wood screws
  • Clamps
  • Pencil and square
  • Safety glasses
  • Masking tape

Step by step

  1. 12.5×

    Pick the screw

    A good length is about 2.5 times the thickness of the piece you are fixing, as long as the tip stays inside the base. Use the screw picker below.

    At least half the screw should end up in the base.

  2. 25 mm+

    Mark and clamp

    Mark each screw with a small cross, at least 25 mm (1 in) from an end and 10 mm from an edge. Clamp the two pieces together exactly where they will go.

    Closer to the end splits the wood, pilot hole or not.

  3. Drill the clearance hole

    Through the top piece only, drill a hole as wide as the screw's smooth shank. The screw slips through it, so the head can pull the top piece down tight.

    No clearance hole? The thread grips both pieces and can hold a gap open.

  4. Drill the pilot hole

    Change to a thinner bit, about as wide as the screw's core. Drill into the base as deep as the screw will go. A flag of masking tape on the bit marks the depth.

    Hardwood needs a slightly bigger pilot than softwood.

  5. Countersink

    For flat (countersunk) heads, cut a shallow cone at the top of the clearance hole so the head sits flush. Go a little at a time and try a screw in it.

    Many screws have nibs under the head that countersink softwood on their own.

  6. PZPHTorx

    Match the bit, set the clutch

    Use the bit that fits the head exactly: PZ2 for most Pozidriv screws, PH2 for Phillips, or the right Torx or square size. Set the clutch low and go up a step if the screw stops short.

    A worn or wrong bit slips and chews the head (cam-out).

  7. Drive it straight

    Hold the drill in line with the screw and press firmly so the bit stays in the head. Start slow, then steady. Stop when the head is flush.

    Look from the side as well as the front to check it is straight.

  8. Check the joint

    The pieces should be pulled tight with no gap and the head flush or just below the surface. Do not keep turning once it is home: that strips the hole.

    Stripped? Use a slightly longer or thicker screw, or move along a little.

Screw picker

Type the two thicknesses. The screw goes through the top piece and into the base.

    Drill sizes table
    Screw lengthDiameterGaugeClearancePilot, softwoodPilot, hardwood
    up to 20 mm3.0 mm#53.5 mm1.5 mm2.0 mm
    21 to 30 mm3.5 mm#64.0 mm2.0 mm2.5 mm
    31 to 50 mm4.0 mm#84.5 mm2.5 mm3.0 mm
    51 to 80 mm5.0 mm#105.5 mm3.0 mm3.5 mm
    over 80 mm6.0 mm#126.5 mm3.5 mm4.0 mm

    General woodworking guidance rounded to common drill sizes. Screw makers' charts differ a little: if the box gives sizes, use those.

    Name the parts

    Put the steps in order

    Call a professional when

    • The screws hold up something heavy over people (a high cabinet, a handrail, a child's bed or a swing): ask a carpenter to check the fixing.
    • You are fixing into a wall and are not sure what is behind it: check for cables and pipes, and call an electrician or plumber if you hit one.
    • A screw has snapped off flush with valuable or antique wood: a joiner can extract it cleanly.
    • The job is structural (decks, stairs, floors, roofs): use the screws and spacing the design or building rules say.

    Check yourself

    What it does

    This lesson shows you how to screw one piece of wood to another so the joint pulls up tight and the wood does not split. Eight illustrated steps take you from choosing the screw to driving it flush, each with a Done tick. The screw picker suggests a screw length and thickness for your two pieces, with the clearance and pilot drill sizes for softwood or hardwood. Tap the cut-away picture to learn the parts of a screw and its holes, put the steps in order, and take the quiz.

    It is the second lesson of the free Light carpentry course. Cut your pieces first with a straight saw cut, then use both skills to build a simple shelf and check its fixings with shelf load.

    How to use it

    1. Read the Stay safe box. Unplug or take the battery out before you change a bit.
    2. Type the thickness of the piece you are fixing (the top piece, which the screw passes through) and of the base it goes into, and pick softwood or hardwood. The picker suggests a screw and drill sizes.
    3. Follow the steps on a scrap first, ticking each one. Ticks are only kept if you tick Remember my ticks on this device.
    4. Tap the parts of the picture, put the steps in order, then take the quiz.

    What each hole does

    • Clearance hole: drilled through the top piece, as wide as the screw’s smooth shank. The screw slides through without gripping, so its head can pull the top piece down tight. Without it, the threads grip both pieces and can hold them apart (a gap you cannot close).
    • Pilot hole: a thinner hole in the base, about as wide as the screw’s core (the solid middle without the thread). It makes room so the wood is not wedged apart and split, and it guides the screw in straight. Hardwood needs a slightly bigger pilot than softwood.
    • Countersink: a cone-shaped recess at the top so a countersunk (flat) head sits flush instead of sticking up or crushing the surface.
    • Clutch: the numbered ring on a drill driver. It slips at a set twist, so the screw stops when it is home. Start low and go up a step at a time.

    Worked example

    You are fixing an 18 mm (¾ in) pine board onto a 45 mm (1¾ in) batten. About 2.5 times 18 mm is 45 mm, and the tip stays 13 mm inside the batten, so a 45 mm screw works. That length is usually 4.0 mm thick (#8). Drill a 4.5 mm clearance hole through the board, a 2.5 mm pilot hole about 27 mm deep into the batten (as deep as the screw will go) (3 mm for oak or other hardwood), countersink, then drive the screw with a PZ2 bit and the clutch on a low setting. The screw goes 27 mm into the batten, 60% of its length, which grips well.

    FAQs

    Do I always need a pilot hole? Modern “wood screws” with sharp, cutting tips often go into softwood without one, away from the ends. Always drill a pilot in hardwood, within about 25 mm (1 in) of an end, and in thin or narrow pieces.

    PZ or PH bit? Pozidriv (PZ) heads have extra small lines between the arms of the cross; Phillips (PH) do not. A PH bit in a PZ screw slips and chews the head. Most wood screws in the UK and Europe are PZ2; in North America many are Phillips, square (Robertson) or Torx.

    Why did the screw head snap? Too much force in hard wood without a big enough pilot. Use a larger pilot, a little wax on the thread and a lower clutch setting.

    How far from the end should a screw go? As a rough guide, at least 25 mm (1 in) from an end and 10 mm from an edge, with a pilot hole. Closer than that splits easily.

    Where the numbers come from

    • Screw length rule of thumb (about 2.5 times the thickness of the piece being fixed, with the tip kept inside the base) and the pilot and clearance drill sizes are general woodworking guidance, rounded to common drill sizes; screw makers' charts differ a little. Check the box or the maker's table for your screws.
    • Imperial gauges are the nearest common size to the metric diameter (#6 is about 3.5 mm, #8 about 4.2 mm, #10 about 4.8 mm). Drawings are fibub's own.

    Standard scientific values, such as constants, atomic weights and melting points, are facts found in every textbook; we name where ours were checked. If you are an author or publisher and want a value, a credit or a table changed or removed, tell us and we will act quickly.

    Last updated 2026-11-16.

    Change log for Drill and screw wood

    1. Light carpentry course: saw a straight cut (#L376), drill and screw wood (#L377), build a simple shelf (#L378), shelf load (#T1012) Details on GitHub

    Every change to fibub

    Related tools

    Saw a straight cut #L376 Saw a straight, square cut in wood with a handsaw in seven illustrated steps: mark a square line, clamp the work, cut on the waste side of the line, start with short strokes and let the saw do the work. Try the kerf sim to see why the side of the line matters. Build a simple shelf #L378 Make a wooden wall shelf from one board and two brackets in nine illustrated steps: plan the size and load, cut and sand the board, screw on the brackets, finish it and hang it level. Label the parts, put the steps in order and check yourself. Shelf load #T1012 Work out how hard a wall shelf pulls on each screw. Type what goes on it (or pick books, plates or plants), the shelf depth and the bracket size, and see the pull-out and downward load per screw in kg and newtons, compared with your wall fixing's rating, with a side-view drawing of the forces. Change a flat tyre #L370 Change a flat car tyre onto the spare in eight illustrated steps: get safe, loosen the nuts, jack at the right point, swap the wheel and tighten in a star pattern. Tick each step, name the parts, and print the checklist for your glovebox. Plug a tyre puncture #L371 Plug a nail or screw hole in a tubeless car tyre with a string plug kit in eight illustrated steps, check first whether the hole can be repaired at all, and learn why most tyre makers treat an outside plug as a temporary fix. Fix a bike puncture #L372 Patch a bicycle inner tube in nine illustrated steps: take the wheel off, lever the tyre off, find the hole and the thorn, roughen, glue, patch and refit without pinching. Name the parts of a bike wheel and test yourself.