Home / Learn / Exam prep / IIT JAM Physics / Lesson 2.8
All lessons

Module 2: Mechanics and properties of matter · Lesson 2.8 · about 45 min

Fluids: surface tension, viscosity and Bernoulli

Surface tension and surface energy, pressure inside drops and bubbles, capillary rise, viscosity and Stokes' law, terminal speed, Poiseuille flow and the Reynolds number, continuity, Bernoulli's equation, Torricelli's law, the Venturi meter, draining tanks and rotating liquids.

Key points, meanings and formulas on one page: choose "Save as PDF" in the print box.

Module 2 · about 45 minutes. By the end you will be able to find the pressure inside a drop or bubble, the height of a capillary column, the terminal speed of a sphere, the flow through a narrow tube and the speed of a jet, and you will know which of Bernoulli’s assumptions each problem quietly breaks.

A liquid's surface behaves like a stretched skin, its inside resists sliding past itself, and when it flows smoothly without friction its pressure, speed and height trade energy along each streamline.

1. Surface tension and surface energy

Molecules at a surface have fewer neighbours to attract them, so making new surface costs energy. Surface tension T is that energy per unit area (J/m²), or equally the force per unit length (N/m) with which the surface pulls along any line drawn in it. A soap film in a wire frame has two surfaces, so a sliding wire of length l feels 2Tl.

Because a surface wants to be as small as possible, small drops are spheres. Merging drops releases energy: eight drops of radius r make one of radius 2r, cutting the area from 32πr2 to 16πr2 and warming the liquid slightly.

Excess pressure. A curved surface pushes inwards, so the pressure on its concave side is higher:

Δpdrop=2Tr,Δpsoap bubble=4Tr (two surfaces),Δpair bubble in liquid=2Tr

Smaller means higher pressure: joined by a tube, a small soap bubble empties into a big one.

Worked example. An air bubble of radius 0.1 mm is 10 cm under water (T=0.072 N/m). Inside, the pressure exceeds the atmosphere’s by ρgh+2T/r=980+1440=2420 Pa.

2. Contact angle and capillary rise

Where a liquid meets a solid it makes a contact angle θ. If the liquid sticks to the solid more strongly than to itself (water on clean glass), θ<90∘ and it climbs a narrow tube; if not (mercury on glass), θ>90∘ and it is pushed down. Balancing the upward pull 2πrTcos⁡θ against the weight of the column gives Jurin’s law:

h=2Tcos⁡θρgr

Half the radius, twice the height. Between two plates a gap d apart the rise is 2Tcos⁡θ/ρgd. If the tube is shorter than h, the liquid stops at the top with a flatter meniscus; it never overflows. Only half the surface energy released ends up as potential energy of the column; the rest is heat. Explore it with the capillary rise tool.

3. Viscosity, Stokes’ law and terminal speed

Layers of a real fluid drag on each other. Newton’s law of viscosity: the shear stress is proportional to the velocity gradient, F/A=ηdv/dy, with η in Pa s. Liquids get less viscous when heated; gases get more viscous, and an ideal gas’s viscosity does not depend on its pressure.

A small sphere moving slowly through a fluid feels Stokes’ drag 6πηrv. Falling, it speeds up until weight, buoyancy and drag balance:

vt=2r2(ρ−σ)g9η

vt∝r2, so fine mist hangs in the air and big drops fall fast. A bubble (ρ<σ) rises at a steady speed. Stokes’ law needs a small Reynolds number Re=ρvD/η, the ratio of inertial to viscous forces; at large Re the flow turns turbulent. See it in the Stokes’ law tool.

Worked example. A steel ball (radius 1 mm, 7800 kg/m³) in glycerine (1260 kg/m³, 1.5 Pa s): vt=2×10−6×6540×9.813.5=9.5 mm/s.

4. Flow through a pipe: Poiseuille’s law

In steady laminar flow through a round pipe, a force balance on a cylinder of fluid of radius s gives Δpπs2=−η(dv/ds)2πsL. Integrate with v=0 at the wall:

v(s)=Δp4ηL(R2−s2),Q=πΔpR48ηL
The speed is a parabola across the pipe: zero at the wall, greatest on the axis, with the average exactly half the maximum. Make the pipe wider and watch the flow rate grow as the fourth power of the radius.

The R4 is why narrowed arteries matter so much: a 10% wider pipe carries 46% more. Tubes in series add their resistances 8ηL/πR4 like resistors, and the narrowest tube takes most of the pressure drop.

T (surface tension)
energy per unit area of surface, or pull per unit length along it
2T/r, 4T/r
extra pressure inside a curved surface (one surface, or a soap film's two)
η (viscosity)
how strongly neighbouring layers drag on each other
R⁴ in Poiseuille's law
wider pipes: more area and faster flow at the same time
Physical meaning
Surface tension decides shapes and climbs in small things, viscosity decides how slowly things flow and settle, and in a wide, fast flow inertia takes over.

5. Continuity and Bernoulli’s equation

For an incompressible fluid, what flows in must flow out: A1v1=A2v2. For steady, incompressible, non-viscous flow, energy per unit volume is constant along a streamline:

p+12ρv2+ρgh=constant
A Venturi tube. The water speeds up in the throat, so its pressure must drop there, as the lower column shows. Change the area ratio and the flow speed.

Three classic uses:

  • Torricelli: a jet from a hole at depth h leaves at 2gh. From a tank of depth H on the ground it lands 2h(H−h) away, farthest for a hole half way down.
  • Venturi meter: with A1=kA2, Δp=12ρv12(k2−1) gives the flow from a pressure reading.
  • Lift: air faster over a wing than under it means lower pressure on top.

Draining a tank. Adh/dt=−a2gh makes h fall linearly in time: the time to empty is Aa2H/g, and three quarters of the water leaves in the first half of that time.

Worked example. A Venturi meter with areas 20 cm² and 10 cm² shows 3000 Pa. Then 3000=12(1000)(4−1)v12, v1=1.41 m/s and Q=2.83 L/s. Watch streamlines and pressure change in the Bernoulli flow tool.

“Fast-moving fluid pushes harder, so the pressure in a narrow, fast section is higher.” It is lower. Pressure is what a gauge moving with the fluid would read, and the fluid speeds up into the constriction precisely because the pressure ahead of it is lower. The faster the flow, the lower the pressure, as long as Bernoulli’s assumptions hold.

6. Liquids in rotating and accelerating containers

In a frame that rotates or accelerates, add the fictitious force to gravity; the free surface lies perpendicular to the total. A bucket spinning at ω has a paraboloid surface, z=ω2s2/2g, so the water at the wall stands ω2R2/2g higher than at the centre. A U-tube accelerating at a along the line of its arms (a distance L apart) shows a level difference aL/g: a simple accelerometer. For floating bodies and buoyancy, the floating and buoyancy tool lets you test Archimedes’ principle.

  • Surface tension: energy per area = force per length. Drop 2T/r, soap bubble 4T/r, air bubble in liquid 2T/r.
  • Capillary rise h=2Tcos⁡θ/ρgr; mercury (θ>90∘) is depressed; half the surface energy becomes potential energy.
  • Viscosity F/A=ηdv/dy; Stokes 6πηrv; terminal speed 2r2(ρ−σ)g/9η; low Re=ρvD/η means laminar.
  • Poiseuille: parabolic profile, average = half the maximum, Q=πΔpR4/8ηL.
  • Continuity Av = constant; Bernoulli p+12ρv2+ρgh = constant (steady, incompressible, non-viscous, along a streamline).
  • Torricelli 2gh; draining time (A/a)2H/g; rotating liquid rises ω2R2/2g at the wall.

Practise: exam questions on this lesson

They start easy and climb to top-rank level. More on the fluids practice page.

Before this: lesson 2.7, elasticity. Next: lesson 2.9, special relativity. Gas viscosity from molecular motion comes back in kinetic theory.

Go deeper: GATE Physics has no fluids lesson; the nearest next step is CSIR NET’s kinetic theory of transport, which derives viscosity from molecular collisions.

Check yourself

1A soap bubble and a water drop have the same radius and the same surface tension. Compared with the drop, the excess pressure inside the bubble is
2Water flows along a horizontal pipe into a narrower section. In the narrow section the pressure is
3In laminar flow through a narrow tube, the flow rate depends on the radius r as

Sources

  • D. S. Mathur, Elements of Properties of Matter (S. Chand), chapters on surface tension and viscosity
  • D. J. Acheson, Elementary Fluid Dynamics (Oxford, 1990), chapters 1 and 2
  • P.-G. de Gennes, F. Brochard-Wyart and D. Quéré, Capillarity and Wetting Phenomena (Springer, 2004), chapter 1
  • IIT JAM Physics syllabus (Mechanics and General Properties of Matter), published by the organising IIT each year

Your ticks stay in this browser. Save them as a file on the course home.

Updated 2026-11-22. Not affiliated with IIT or the JAM organising institute. Exam pattern as published for recent years: always check the official JAM website before the exam. All questions are original.