Home / Learn / Exam prep / IIT JAM Physics / Lesson 7.5
All lessons

Module 7: Solid state physics and electronics · Lesson 7.5 · about 45 min

Transistors and amplifiers

How a bipolar transistor turns a small base current into a large collector current, how to bias it with a load line and a stable Q-point, how to get the gain of common-emitter, common-base and emitter-follower stages in one line, and how JFETs and MOSFETs differ.

Key points, meanings and formulas on one page: choose "Save as PDF" in the print box.

Module 7 · about 45 minutes. By the end you will be able to explain transistor action from the physics of a p-n junction, use α and β without mixing them up, draw a load line and place a Q-point, tell at a glance whether a transistor is active, saturated or cut off, and write down the gain and impedances of the common-emitter, common-base and common-collector stages. A short section on JFETs and MOSFETs closes the lesson.

A transistor is a valve: a small current into the base (or a small voltage on the gate) controls a much larger current through the device, and a resistor turns that controlled current into an amplified voltage.

1. Two junctions, one very thin layer

A bipolar junction transistor (BJT) is a sandwich of three doped regions: n-p-n or p-n-p. The three regions are

Region Doping Size Job
Emitter heavy medium injects carriers into the base
Base light very thin lets almost all of them pass
Collector moderate largest collects them and gets rid of the heat

There are two p-n junctions: base-emitter (BE) and base-collector (BC). In the npn transistor the arrow on the emitter of the circuit symbol points out (current leaves the emitter); in the pnp it points in. Everything below is for npn; for pnp reverse every voltage and current.

2. Transistor action

Here is what happens inside an npn transistor biased for amplification, with the BE junction forward biased and the BC junction reverse biased:

Injection. The forward-biased BE junction lets the heavily doped emitter push a flood of electrons into the base. (Holes from the base also cross into the emitter, but the base is lightly doped, so they are few.)

Diffusion across a thin base. In the p-type base the electrons are minority carriers. They spread out by diffusion. The base is so thin, and has so few holes, that only about 1 in 100 of them meets a hole and recombines.

Collection. At the far side the reverse-biased BC junction has a strong electric field pointing from collector to base. It sweeps every electron that arrives into the collector. A reverse bias does not stop minority carriers; it helps them.

Bookkeeping. The few electrons that recombine in the base must be replaced through the base lead: that is the small base current I_B. The rest form the collector current I_C. So I_E = I_B + I_C, with I_C close to I_E.

Control. The base current sets how hard the BE junction is driven, and so how many electrons are injected. A small change in I_B gives a change in I_C about β times larger. That is amplification.

Two numbers describe the current split:

α=ICIE (just under 1),β=ICIB (typically 50 to 300),β=α1−α,α=β1+β

Kirchhoff’s current law for the whole device gives IE=IB+IC=(β+1)IB. A tiny leakage ICBO flows across the reverse-biased BC junction even with the emitter open; with the base open it is amplified to ICEO=(β+1)ICBO.

α
the fraction of the emitter current that reaches the collector (common-base current gain)
β
how many times larger the collector current is than the base current (common-emitter current gain)
I_E = I_B + I_C
charge is conserved: what goes in through base and collector comes out of the emitter
Physical meaning
β is huge because recombination in the base is rare. A change of α from 0.99 to 0.995 doubles β, so β varies a lot between transistors while α hardly moves. Good circuits are designed not to depend on β.

Worked example. A transistor has β=150 and carries IE=4.53 mA. Find IB, IC and α.

  1. IB=IE/(β+1)=4.53/151=0.030 mA =30 μA.
  2. IC=βIB=150×30 μA=4.50 mA. Check: 4.50+0.03=4.53 mA.
  3. α=β/(1+β)=150/151=0.9934.

The usual slip is dividing IE by β instead of β+1.

3. The four modes

The two junctions can each be forward or reverse biased, giving four modes:

BE junction BC junction Mode Behaviour
forward reverse active IC=βIB: amplifier
forward forward saturation VCE≈0.2 V, IC<βIB: closed switch
reverse reverse cut-off IC≈0: open switch
reverse forward inverse active rarely used; poor gain

The test in a problem: assume active, work out IC=βIB and then VCE. If VCE comes out above about 0.2 V, the assumption holds. If it comes out negative, the transistor is saturated and IC is set by the outside circuit instead: IC≈(VCC−VCE,sat)/RC.

4. Characteristics, the load line and the Q-point

The input characteristic (I_B against V_BE) is just a forward-biased diode: almost nothing below 0.6 V, then a steep rise. The output characteristics are a family of curves of I_C against V_CE, one for each I_B. Each curve rises steeply for the first few tenths of a volt (saturation), then runs almost flat (active region) at IC≈βIB.

The curves are not perfectly flat. As V_CE grows, the BC depletion layer widens into the base and makes it thinner, so fewer carriers recombine and I_C creeps up. This is base-width modulation, the Early effect. Extended backwards, the sloping lines meet the V_CE axis near −VA, the Early voltage (tens to hundreds of volts).

The resistor RC adds a second rule. Kirchhoff’s voltage law round the collector loop gives the DC load line:

VCE=VCC−ICRC

It is a straight line from (VCC,0) on the voltage axis to (0,VCC/RC) on the current axis. The transistor must sit on its own curve AND on the load line, so the operating point, the Q-point (quiescent point), is where they cross.

Move the base current and the Q-point slides along the load line. Push I_B high (or R_C large) and Q runs into saturation at the left; set I_B to zero and it drops to cut-off at V_CE = V_CC. Changing R_C pivots the line about its V_CC end.

For an amplifier the Q-point should sit near the middle of the active region, so the signal can swing both ways without hitting saturation (the bottom of the output is flattened) or cut-off (the top is flattened). Because a CE stage inverts, a Q-point too close to cut-off clips the positive half of the output, which comes from the negative half of the input.

Worked example. A CE stage has VCC=10 V and RC=2 kΩ, and the transistor (β = 100) gets IB=30 μA. Find the Q-point.

  1. Assume active: IC=100×30 μA=3 mA.
  2. VCE=10−3×2=4 V, comfortably above 0.2 V, so active it is.
  3. If instead IB=60 μA, the formula gives IC=6 mA and VCE=−2 V: impossible, so the transistor saturates with IC≈(10−0.2)/2=4.9 mA.

5. Biasing for a Q-point that stays put

Fixed bias (one resistor RB from VCC to the base) sets IB=(VCC−0.7)/RB. But IC=βIB, and β changes from one transistor to the next and rises with temperature. So the Q-point wanders. Its stability factor S=∂IC/∂ICBO=1+β is as bad as it gets.

Voltage-divider bias fixes the base VOLTAGE with two resistors R1 (top) and R2 (bottom), and puts a resistor RE in the emitter. If IC tries to rise, the emitter voltage rises, VBE falls and pushes IC back: negative feedback. When the divider current is much larger than IB:

VB=VCCR2R1+R2,IC≈IE=VB−VBERE,VCE=VCC−IC(RC+RE)

None of these contains β. The stability factor is S=(1+β)1+Rth/RE1+β+Rth/RE, close to 1 when the Thevenin resistance of the divider Rth=R1∥R2 is small compared with RE.

Worked example. VCC=12 V, R1=47 kΩ, R2=10 kΩ, RE=1 kΩ, RC=2.2 kΩ, β large.

  1. VB=12×10/57=2.105 V.
  2. VE=2.105−0.7=1.405 V, so IC≈1.405 mA.
  3. VCE=12−1.405×(2.2+1)=7.50 V. Active, near the middle of the 12 V supply.

If β is only about 100, treat the divider as its Thevenin equivalent (Vth in series with Rth) and solve Vth=IBRth+VBE+(β+1)IBRE; the answer drops by a few per cent. Try your own numbers here:

6. The transistor as a small-signal amplifier

Around the Q-point a small signal sees a simple linear model. Because IC=ISeVBE/VT (with VT=kT/e≈25 mV at room temperature), a small change in VBE changes IC at the rate

gm=∂IC∂VBE=ICVT,re=VTIE≈1gm,rπ=βgm=(β+1)re

gm is the transconductance (40 mA/V at 1 mA), re the resistance looking into the emitter (25 Ω at 1 mA) and rπ the resistance looking into the base. In h-parameter language hfe=β, hie=rπ, and hoe is the small slope of the output curves caused by the Early effect.

Common-emitter gain. A signal vin on the base changes the collector current by gmvin. That current flows through RC in parallel with any capacitively coupled load RL:

Av=−gm(RC∥RL)(emitter bypassed),Av≈−RC∥RLre+RE(RE unbypassed)

The minus sign is the 180° phase reversal. An unbypassed RE lowers the gain but makes it depend on resistors instead of the transistor, raises the input resistance to (β+1)(re+RE) and widens the bandwidth: the classic trade of gain for stability.

Worked example. A CE stage at IC=2 mA has RC=4.7 kΩ, a 10 kΩ load, and an unbypassed 100 Ω emitter resistor.

  1. re=25/2=12.5 Ω; RC∥RL=4.7×10/14.7=3.20 kΩ.
  2. Bypassed, the gain would be −3200/12.5=−256.
  3. With the 100 Ω left in: Av=−3200/(12.5+100)=−28.4. Smaller, but a 20% change in IC now barely moves it.

7. Three ways to connect one transistor

The terminal shared by input and output names the configuration:

Common emitter Common base Common collector (emitter follower)
Input at / output at base / collector emitter / collector base / emitter
Voltage gain large, inverted: −gmRC large, not inverted: +gmRC just under 1: RE/(RE+re)
Current gain β α (just under 1) β+1
Input resistance medium, rπ low, re high, (β+1)(re+RE)
Output resistance high, about RC high low, re+Rs/(β+1)
Used for general voltage gain high frequencies, current buffer buffer: weak source, heavy load

A surprise examiners like: for the same gm and RC, common base has the same size of voltage gain as common emitter. Its current gain is below 1, but its tiny input resistance makes up for it.

Two transistors can be combined: a Darlington pair (emitter of the first into the base of the second) behaves like one transistor with β≈β1β2.

8. Frequency response in brief

An RC-coupled amplifier has a flat mid-band. At low frequencies the coupling and bypass capacitors stop being short circuits: each forms a high-pass filter with the resistance it sees, fL=1/(2πRC). At high frequencies the transistor’s own junction capacitances short the signal. The worst is the base-collector capacitance Cμ: it sits between the input and an inverted, amplified output, so the input sees it multiplied, CM=Cμ(1+|Av|), the Miller effect. Gain times bandwidth stays roughly constant, which is the first hint of the gain-bandwidth product you will meet in the op-amp lesson.

“A transistor is just two diodes back to back.” No. Two separate diodes joined at their anodes cannot amplify: an electron entering one diode recombines long before it could reach the other. Transistor action needs the two junctions to share a base thinner than the distance a minority carrier diffuses before it recombines, so carriers injected by one junction are collected by the other. The “two diodes” picture is useful only for testing a transistor with a meter, never for understanding gain.

9. Field-effect transistors

A JFET is a bar of n-type silicon (the channel) with p-type gates on its sides. The gate junction is kept reverse biased, so almost no gate current flows (input resistance of 109 Ω or more). A more negative gate voltage widens the depletion layers and squeezes the channel. Beyond a small drain voltage the channel pinches off at the drain end and the current saturates at a value set by VGS alone (Shockley’s equation):

ID=IDSS(1−VGSVP)2,gm=2IDSS|VP|(1−VGSVP)

where IDSS is the current at VGS=0 and VP (negative for n-channel) is the pinch-off voltage.

A MOSFET insulates the gate from the channel with a thin oxide, so the DC gate current is essentially zero. An enhancement n-MOSFET has no channel until VGS exceeds a positive threshold VT; in saturation ID=K(VGS−VT)2. A depletion MOSFET is built with a channel and conducts at VGS=0. FETs are unipolar (only majority carriers carry the current) and voltage controlled; BJTs are bipolar and current controlled.

Watch the word “saturation”: in a FET it means the current has levelled off (the amplifying region); in a BJT it means VCE has collapsed (the switch-on region).

Worked example. An n-channel JFET with IDSS=10 mA and VP=−4 V has VGS=−1 V.

  1. ID=10(1−0.25)2=10×0.5625=5.63 mA.
  2. gm=(2×10/4)(0.75)=3.75 mS.
  3. With a 2 kΩ drain resistor the small-signal gain is −gmRD=−7.5: FETs give less voltage gain than BJTs at similar currents, in exchange for their enormous input resistance.

To explore real device curves, the p-n junction tool shows the depletion layer and diode curve that the BE junction follows, the I-V characteristics tool builds a current-voltage graph point by point, and the circuit simulator solves the DC operating point and AC response of any resistor network you type in.

  • BJT action: the BE junction (forward) injects carriers, the thin, lightly doped base lets them through, the BC junction (reverse) collects them. IE=IB+IC, β=α/(1−α), IB=IE/(β+1).
  • Modes: active (BE forward, BC reverse) amplifies; saturation (both forward) and cut-off (both reverse) make a switch. Check VCE to know which.
  • DC load line VCE=VCC−ICRC; the Q-point is where it meets the transistor’s curve. Put it mid-way for the biggest undistorted swing.
  • Voltage-divider bias with RE makes the Q-point nearly independent of β; fixed bias has S=1+β.
  • Small signal: gm=IC/VT, re=VT/IE, rπ=β/gm. CE gain −gm(RC∥RL), or −(RC∥RL)/(re+RE) with an unbypassed RE.
  • CE inverts with high gain; CB has the same gain magnitude but low input resistance; the emitter follower has gain just under 1, high input and low output resistance.
  • JFET: ID=IDSS(1−VGS/VP)2 with the gate reverse biased; MOSFETs have an insulated gate and come as enhancement or depletion types.

Practise: exam questions on this lesson

They start easy and climb to top-rank level. Check each answer, then read the full solution. There are more on the transistors practice page.

Next: lesson 7.6 packs dozens of transistors into one chip, the operational amplifier, and shows how feedback makes its gain depend only on two resistors. Then lesson 7.7 uses transistors as switches to build logic gates. The GATE Physics course takes amplifiers further, with feedback topologies and multistage design, and puts BJTs beside FETs and MOSFETs in semiconductor devices.

Check yourself

1An npn transistor has α = 0.99. What is its common-emitter current gain β?
2In a fixed-bias common-emitter stage, the transistor is swapped for one with a much larger β. What happens to the Q-point?
3Which single-transistor stage has the lowest output impedance and a voltage gain just under 1?

Sources

  • A. S. Sedra and K. C. Smith, Microelectronic Circuits, 7th ed. (2015), chapters 6 and 7: bipolar junction transistors and amplifier basics
  • P. Horowitz and W. Hill, The Art of Electronics, 3rd ed. (2015), chapters 2 and 3: bipolar transistors and field-effect transistors
  • J. Millman, C. Halkias and S. Jit, Electronic Devices and Circuits, 4th ed. (2015), transistor biasing and small-signal chapters
  • IIT JAM Physics syllabus (Solid State Physics, Devices and Electronics section), published by the organising IIT each year

Your ticks stay in this browser. Save them as a file on the course home.

Updated 2026-11-22. Not affiliated with IIT or the JAM organising institute. Exam pattern as published for recent years: always check the official JAM website before the exam. All questions are original.