All lessons

Module 51: Metals and metallurgy · Lesson 51.1 · about 32 min

Metals and metallurgy

Ores and minerals, concentration (gravity, froth flotation, magnetic, leaching), calcination and roasting, reduction and the thermodynamics behind it (Ellingham diagrams), extraction of iron, copper, zinc and aluminium, and refining methods, for KEAM, CUSAT, COMEDK and JEE.

Key points, meanings and formulas on one page: choose "Save as PDF" in the print box.

Chemistry · Class 12 · about 32 minutes. By the end you will be able to choose the right concentration, roasting and reduction steps for an ore, read an Ellingham diagram, describe the extraction of iron, copper, zinc and aluminium, and match each refining method to its metal. This chapter is mainly asked in KEAM, CUSAT, COMEDK and JEE Advanced; check your exam’s current syllabus.

Metals sit in the ground as compounds, mostly oxides and sulphides, mixed with rock. Extraction is three jobs: get rid of the rock (concentration), turn the compound into an oxide, and take the oxygen away (reduction) with something that wants it more. An Ellingham diagram is the chart that tells you which "something" works and how hot it must be.

1. Ores and minerals

A mineral is a naturally occurring compound of a metal; an ore is a mineral from which the metal can be extracted profitably. The unwanted earthy material is gangue.

Metal Main ores
Aluminium bauxite AlOₓ(OH)₃₋₂ₓ (often written Al₂O₃·xH₂O), cryolite Na₃AlF₆
Iron haematite Fe₂O₃, magnetite Fe₃O₄, siderite FeCO₃, iron pyrites FeS₂
Copper copper pyrites CuFeS₂, copper glance Cu₂S, malachite CuCO₃·Cu(OH)₂, cuprite Cu₂O
Zinc zinc blende ZnS, calamine ZnCO₃, zincite ZnO
Lead galena PbS

Iron pyrites is not used for iron (too much sulphur). Reactive metals (Na, Mg, Al) occur as compounds only; gold and platinum occur free (native).

2. Concentration

  • Hydraulic washing (gravity separation): heavy ore particles settle, light gangue is washed away (haematite, tin stone).
  • Magnetic separation: one component is magnetic (magnetite, or wolframite from cassiterite).
  • Froth flotation: for sulphide ores. Oil (pine oil) with collectors (xanthates) wets the sulphide, froth stabilisers (cresols) hold the foam, and air bubbles carry the ore up. Depressants separate two sulphides: NaCN stops ZnS from frothing, so PbS can be floated off first.
  • Leaching: dissolving the ore chemically. Bauxite in hot NaOH (Bayer process): Al₂O₃ dissolves as Na[Al(OH)₄], silica and iron oxide stay behind; CO₂ then precipitates pure Al(OH)₃. Gold and silver in dilute NaCN with air (cyanide process), then displaced by zinc: 2[Au(CN)₂]⁻ + Zn → [Zn(CN)₄]²⁻ + 2Au.

3. Calcination and roasting

Calcination: heating in limited or no air to drive off water or CO₂: ZnCO₃ → ZnO + CO₂; Al₂O₃·xH₂O → Al₂O₃ + xH₂O.

Roasting: heating in air below the melting point, mainly for sulphides: 2ZnS + 3O₂ → 2ZnO + 2SO₂; 2PbS + 3O₂ → 2PbO + 2SO₂. It also burns off arsenic and sulphur impurities. The SO₂ is used for sulphuric acid.

4. Reduction and the Ellingham diagram

For an oxide MO to be reduced by a reducing agent R, the coupled reaction must have negative ΔG°: ΔG°(R → RO) must be more negative than ΔG°(M → MO). An Ellingham diagram plots ΔG° for forming oxides (per mole of O₂) against temperature.

ΔG∘=ΔH∘−TΔS∘
  • Most metal-to-oxide lines slope upward, because a gas (O₂) is used up, so ΔS° is negative.
  • 2C + O₂ → 2CO slopes downward (gas doubles, ΔS° positive). So carbon becomes a better reducing agent the hotter it gets, eventually beating almost any metal.
  • C + O₂ → CO₂ is nearly flat; 2CO + O₂ → 2CO₂ slopes upward.
  • Any element whose line lies below another’s can reduce that other oxide. Where two lines cross, the reduction becomes possible above (or below) that temperature.
  • A sudden change of slope means a phase change (for example, Zn boiling at 1180 K).
Choose an oxide and slide the temperature. The bold lines are the oxide, carbon to CO and CO to CO₂. Where the C → CO line passes below the oxide line, carbon can reduce it. The data are rounded; real lines bend at melting and boiling points.
ΔG°
standard Gibbs energy change for forming the oxide, per mole of O₂ (kJ)
ΔH°, ΔS°
enthalpy change (kJ) and entropy change (kJ/K) of that reaction
T
temperature in kelvin
Gangue, flux, slag
unwanted rock; substance added to remove it; the fusible waste they form (CaO + SiO₂ → CaSiO₃)
Physical meaning
The lower a line, the more an element wants oxygen at that temperature. The lower one steals oxygen from the higher one.

Aluminium cannot be reduced by carbon at practical temperatures: its line is far below. It is made by electrolysis instead. Aluminium itself reduces Cr₂O₃ and Fe₂O₃ (thermite process, aluminothermy), since its line is below theirs.

5. Extraction of four metals

Iron (blast furnace). Charge: haematite, coke and limestone; hot air blown in at the bottom.

  • Bottom (about 2000 K): C + O₂ → CO₂, then CO₂ + C → 2CO.
  • Middle and top (500 to 900 K): Fe₂O₃ + 3CO → 2Fe + 3CO₂ (reduction by CO in the cooler zone). Lower down, FeO + C → Fe + CO.
  • Limestone decomposes to CaO (flux), which removes silica as slag CaSiO₃, which floats on the molten iron.
  • Pig iron (about 4% C) → cast iron (3% C, hard, brittle) → wrought iron (purest, under 0.2% C) or steel (0.2 to 1.5% C plus alloy metals).

Copper from copper pyrites. Froth flotation → roasting (FeS → FeO) → smelting with silica: FeO + SiO₂ → FeSiO₃ (slag), leaving copper matte (Cu₂S + FeS) → in a Bessemer converter, the rest of the FeS is oxidised and slagged, and self-reduction gives copper: 2Cu₂O + Cu₂S → 6Cu + SO₂. Escaping SO₂ leaves a blistered surface: blister copper (98%), then refined electrolytically.

Zinc. Roast ZnS → ZnO, reduce with coke at about 1673 K: ZnO + C → Zn + CO. Zinc boils at 1180 K, so it distils off and is condensed.

Aluminium (Hall-Héroult). Pure Al₂O₃ from the Bayer process is dissolved in molten cryolite with some CaF₂ (lowers the melting point from about 2300 K to about 1250 K and improves conductivity). Steel cell lined with carbon (cathode), graphite anodes. Cathode: Al³⁺ + 3e⁻ → Al. Anode: carbon burns to CO and CO₂, so the anodes must be replaced.

“Roasting and calcination are the same, just with different ores.” Roasting needs air and is an oxidation (sulphide to oxide). Calcination is heating with little or no air and is a decomposition (carbonate or hydrate to oxide). The gas given off tells you which: SO₂ from roasting, CO₂ or water from calcination.

6. Refining

Method Idea Used for
Distillation metal boils lower than impurities Zn, Hg
Liquation metal melts lower, flows off Sn
Electrolytic refining impure anode dissolves, pure metal on cathode; noble metals fall as anode mud (Ag, Au, Pt from copper) Cu, Zn, Al
Zone refining impurities stay in the molten zone as a heater moves along a rod Si, Ge, Ga (semiconductors)
Vapour phase: Mond Ni + 4CO → Ni(CO)₄ at 330 to 350 K, decomposes at 450 to 470 K Ni
Vapour phase: van Arkel M + 2I₂ → MI₄, decomposes on a hot W filament Zr, Ti
Chromatography components move at different rates over an adsorbent elements in tiny amounts

“Electrolytic refining dissolves the impurities into the solution, and they are thrown away.” Only the more reactive impurities (Fe, Zn) dissolve and stay in solution. The less reactive ones (silver, gold, platinum) do not dissolve at all: they drop under the anode as anode mud, which is valuable and is processed for these metals.

  • Froth flotation for sulphides; NaCN depresses ZnS. Leaching: Bayer (bauxite in NaOH), cyanide (Au, Ag).
  • Calcination: no air, decomposition. Roasting: air, sulphide to oxide.
  • Ellingham: lower line reduces the oxide of a higher line; C → CO slopes down, so carbon gets better when hot.
  • Blast furnace: CO reduces Fe₂O₃ at the top; CaO removes SiO₂ as slag.
  • Copper: matte, then self-reduction in a converter to blister copper.
  • Aluminium: electrolysis of Al₂O₃ in molten cryolite; carbon anodes burn away.
  • Refining: zone (Si, Ge), Mond (Ni), van Arkel (Zr, Ti), electrolytic (Cu) with anode mud.

Check yourself

1Froth flotation is used mainly to concentrate:
2In an Ellingham diagram, the line for 2C + O₂ → 2CO slopes downwards because:
3Which metal is refined by the van Arkel method?

Sources

  • JEE Main and JEE Advanced 2026 syllabi; KEAM, CUSAT CAT and COMEDK chemistry syllabi (metallurgy is not in the current NEET syllabus; check each exam's latest notice)
  • Standard Gibbs energies of formation for Ellingham lines: NIST-JANAF Thermochemical Tables https://janaf.nist.gov
  • IUPAC Gold Book: ore, mineral, gangue, flux, slag https://goldbook.iupac.org

Your ticks stay in this browser. Save them as a file on the course home.

Updated 2026-11-22. Syllabus and exam patterns follow the official notices checked on 2026-11-22; they can change every year, so check the official exam website. All questions are original fibub work, not copied from past papers or books. Nothing you do here is sent anywhere.